28 June 2024 in IEEE Transactions on Applied Superconductivity
The AC loss of the high temperature superconducting (HTS) cable with joints is a key factor to estimate the cooling effect of the HTS cable. In this work, an artificial intelligence-based model is proposed to predict the AC loss of REBCO lap joints when carrying alternating current. The training data was obtained from simulation by a 3-D lap joint model based on H-formulation. The artificial intelligence-based model is demonstrated to evaluate the effect of inhomogeneity of joint resistance on AC loss. It is shown that the AC loss of lap joints in the cable is increased when the nonuniformity of joint resistance is higher. The proposed model can increase the speed of calculating the statistical results depending on the mass of investigating data.
29 July 2024 in IEEE Transactions on Applied Superconductivity
The alternating current (AC) losses of the multi-channel high temperature superconducting (HTS) twisted stacked tape cable-cable in conduit conductor (TSTC-CICC) composed of second-generation (2G) HTS tapes were studied using the T-A formulation and the three-dimensional (3D) finite element method. In this paper, the transport and magnetization AC loss of four-channel TSTC-CICC conductors with two different tapes stacking arrangements (Structure-I and Structure-II) were calculated, in the case that different torsion, transport currents and external magnetic fields. The results show that the transport and magnetization losses of the two types of conductors are positively correlated with the torsion of the conductor, under the condition that the same transport current and external magnetic field. When the torsion of the conductor is the same, the transport losses of the two types of conductors increase with the increase in current, while the magnetization losses enhance with the increase of the magnetic field. When the torsion is 0.06 m, the transport losses of Structure-I are smaller than those of Structure-II in the situation of the same transport current. Under the same external magnetic field conditions, the magnetization losses of Structure-I are higher than those of Structure-II. In presence of the imposed magnetic field, the shielding currents that permeate from the border of the stacked tapes to the middle of the tapes are generated inside the stacked tapes of the conductors, but the distributions of the shielding currents in each channel of the two types of conductors are different.
28 July 2016 in Journal of Composite Materials
A novel method of characterizing moisture effect on mechanical performance of epoxy resin is presented in this paper. A 50-µm-thick layer of cured epoxy resin was fabricated and cut into strips of 4 mm wide and 30 mm long as specimens to be tested on a dynamic mechanical analyzer equipped with thin-film tension clamp. Static tension and force-controlled tension–tension fatigue tests were first carried out using thin-film specimens made from Momentive 135/137 and BASF 5400/5440 epoxy resin systems without applying moisture, and results were compared with those obtained using conventional dog-bone specimens to validate the proposed testing method. Another batch of thin-film specimens were then immersed into deionized water, and the weight gain was recorded regularly until full saturation to obtain the absorption curve. Static and fatigue tests were performed using thin-film specimens made from BASF 5400/5440 with 55% and 100% saturation of moisture respectively, to evaluate moisture-induced material degradation. The aging effect on BASF 5400/5440 caused by cyclic water immersion and drying process was also assessed by performing static and fatigue tests using fully dried thin-film specimens after aging. It was concluded that the combination of thin-film specimen and dynamic mechanical analyzer would yield as good measurements of tensile strength and fatigue life as conventional dog-bone specimen does, and the small thickness of thin-film specimen would greatly reduce the time to reach a certain level of moisture content, facilitating further studies on effect of moisture ingression on polymeric matrix composites using multi-scale approaches.
18 September 2024 in IEEE Transactions on Applied Superconductivity
Quench propagation characteristics are the key issue for high temperature superconductor (HTS) cables and magnets. In this work, the effect of magnetic field on minimum quench energy (MQE) and the normal zone propagation velocity (NZPV) of two types of HTS tapes, including Bi-2223 and REBCO, are studied by experimental method in 77 K, respectively. The equivalent heat capacity of the two tapes was used to evaluate the MQE property. The experimental results show that the MQE of HTS tape is sensitive to the magnetic field, whereas the NZPV of HTS tape shows less sensitivity to the magnetic field. Although the volume heat capacity of REBCO tape and Bi-2223 tape is similar, the equivalent heat capacity of samples shows a higher difference and leads to the lower MQE for REBCO tape. It is also shown that the NZPV of Bi-2223 tape is smaller than that of REBCO tape.
30 October 2024 in Cryogenics
8 September 2021 in IEEE Transactions on Applied Superconductivity
In this work, the mechanical lap joint of commercial ReBCO tape from SHSC is prepared. The tape is reinforced with stainless steel bar in both side to reduce the effect of bending moment in the joint tensile test. We use Indium and GaInSn as interlayer material, respectively, and different pressures are applied on the joint by jig during testing. The relationship between joint resistance and applied tensile stress was measured at 77 K. The results shows that for all measured joints under pressure, the voltage rise duo to tensile stress is small at first and then sharply grows until a certain value of stress is reached. The maximum tensile stress is higher for the joint which has lower resistance. Comparing two types of mechanical lap joints with Indium and GaInSn, the former joint shows smaller dispersion on joint resistance than the latter under pressure above 40 Mpa. It is also shown that the joint with Indium can tolerate higher tensile stress than the joint with GaInSn by using the Weibull distribution function analysis.