12 July 2021 in IEEE Transactions on Nuclear Science
This paper presents a low-power highly-linear multi-channel data acquisition (DAQ) system for silicon photomultiplier (SiPM) readout. A low-input impedance current-mode front-end with a programmable current gain is developed to achieve high-precision charge readout over a large dynamic range. An integrated 10-bit successive-approximation-register (SAR) analog-to-digital data converter (ADC) shared by 16 readout channels in a time-multiplexed manner is designed to reduce the overall chip area and power consumption of the SiPM readout. Implementation challenges of field-programmable gate array (FPGA)-based time-to-digital converters (TDCs) including bubble error, zero length bins, inter-clock region nonlinearity, and chain overflow, are addressed for high accuracy timing measurement. Multi-chain averaging is developed to improve the TDC linearity. Fabricated in a 180 nm CMOS process, the current-mode 16-channel readout application-specific integrated circuit (ASIC) achieves 3.6% maximum gain nonlinearity over an input dynamic range of 800 pC with dissipating 3.89 mW of power per readout channel, and the ADC achieves an SFDR of 58.34 dB and an SNDR of 51.37 dB at 16 MS/s. Implemented in a Xilinx 28 nm Kintex-7 FPGA, the 32-channel TDC achieves a 15 ps root mean square (RMS) resolution, a differential nonlinearity (DNL) of less than 4 ps, and an integral nonlinearity (INL) of less than 10 ps.
18 March 2022 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article presents a 5-GS/s 6-bit flash analog-to-digital converter (ADC) in a 28-nm fully depleted silicon-on-insulator (FDSOI) CMOS process. The ADC jointly employs partially active second-stage comparison and $2\times $ time-domain latch interpolation (TDI) to reduce power consumption and avoid extensive calibrations. To enhance the conversion speed of the second-stage structure, the stringent timing constraint is resolved by a 25%–75% duty-cycle clock scheme, a 0.5-bit redundancy in the first comparison stage, and an embedded second-stage slice selection logic. The bandwidth requirements of the track-and-hold (T/H) and T/H buffer under the 25%–75% duty-cycle clock are analyzed. An on-chip successive-approximation (SA)-based comparator offset calibration scheme utilizing FDSOI back-gate bias is also developed, providing sufficient calibration range without impairing comparator speed. The measured prototype achieves a signal-to-noise and distortion ratio (SNDR) of 32.8 dB and a spurious-free dynamic range (SFDR) of 41.82 dB at Nyquist frequency while consuming 15.07 mW power, translating into a Walden figure-of-merit (FOM) of 84.5 fJ/conversion-step.
16 March 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents a 24 GHz dual-mode frequency synthesizer designed in a 55-nm CMOS technology supporting both Doppler and frequency modulated continuous wave (FMCW) radars. The effects of chirp linearity and delta-sigma modulation (DSM) resolution on the rms FM error is analyzed. A design procedure for the PLL loop bandwidth and time interval of the frequency step to reduce the rms FM error is proposed. A voltage-controlled oscillator (VCO) featuring a four-coil transformer load is developed providing differential local oscillation (LO) signals for the transmitter (TX) and quadrature LO signals for the 2-channel receiver (RX). The prototype is designed with a loop bandwidth of 350 kHz, a frequency step time interval of $2 ~\mu s$ , and a VCO tuning linearity of 26%. In the FMCW mode, it achieved an rms FM error of 68.8 kHz over a 1.25 GHz chirp bandwidth. In the Doppler mode, the VCO operates in the free-running mode to save power consumption. An 8-bit digital-to-analog converter (DAC) is used to provide the VCO control voltage compensating process and voltage variations. The free-running VCO operates at a 24.125 GHz and has a frequency error of less than 1 MHz.
31 January 2023 in IEEE Transactions on Nuclear Science
This paper presents an on-chip fast signal generator and a successive-approximation-register (SAR) analog-to-digital data converter (ADC) for silicon photomultiplier (SiPM) readout applications. The high-pass filter (HPF)-based fast-signal generator sharpens the rising edge of the standard SiPM output signal reducing time jitter due to the dark counts of the detector. It is implemented by leveraging the equivalent resistance of the current mirror transistor and the AC-coupling capacitor between the current mirror and the current discriminator to avoid hardware and power consumption overhead. Compared with off-chip solutions, the on-chip approach eliminates the packaging pins and high-speed buffers needed for carrying the fast signals reducing packaging complexity and power consumption of the readout system. The energy quantizer utilizes the SiPM charge integrator as the ADC track-and-hold (T/H) circuit to improve the front-end power efficiency. The fast signal generator and the SAR ADC are implemented in a current-mode application-specific integrated circuit (ASIC) designed in a 0.18 μm CMOS technology. Measurement results show that the on-chip fast signal generator is effective in improving the timing performance of the readout system. The timing resolutions are measured using SensL’s 3×3 mm 2 SiPM device with a terminal capacitance of 850 pF using an ultrashort laser pulser. Measurement results show that the fast signal generator improves the timing resolution by 23.4% compared with timing measurement using the standard output signal when the output charge is 300 pC. The ASIC achieved a measured ADC signal-to-noise-distortion ratio (SNDR) of 53.08 dB and a spurious-free dynamic range (SFDR) of 62.74 dB at 1 MS/s and a maximum front-end gain non-linearity of 3.3% over 20-800 pC input charge range while dissipating 4.1 mW of power from a 1.8 V supply.
18 February 2026 in IEEE Transactions on Microwave Theory and Techniques
This article presents a Doppler-assisted frequency-modulated continuous-wave (FMCW) radar that combines precise range resolution capability of FMCW with high sensitivity of Doppler radar, enabling versatile performance for indoor applications. A comprehensive analysis of low-frequency noise contributions from key receiver (RX) blocks including low-noise amplifier (LNA), mixer, local oscillator (LO) buffer, and analog baseband (ABB) circuits is conducted. An “RF+LO+BB” joint noise figure (NF) improvement method is proposed to effectively suppress the low-frequency noise. To minimize frequency modulation (FM) error in charge-pump-based fractional-N phase-locked loops (PLLs), a nested-PLL architecture with an optimized loop parameter selection method is employed, significantly enhancing chirp linearity. Fabricated in a 55-nm CMOS technology, the proposed Doppler-assisted FMCW radar achieves NFs of 32.13 and 12.94 dB at 10 Hz and 1 kHz, respectively, and a chirp linearity of 0.0039% over a 3.52 GHz chirp bandwidth (BW), resulting in a maximum detection range of 19.41 m and a range resolution of 4.7 cm. The radar occupies a die area of 12.7 mm2 and consumes 594 mW in FMCW mode and 432 mW in Doppler mode under a 3.3 V supply.