Institute of Materials for Electronics and Energy Technology (i‐MEET) Department of Materials Science and Engineering Friedrich‐Alexander‐Universität Erlangen‐Nürnberg Martensstrasse 7 91058 Erlangen Germany
Auto-generated profile, based on publicly available information
Tian Du
Institute of Materials for Electronics and Energy Technology (i‐MEET) Department of Materials Science and Engineering Friedrich‐Alexander‐Universität Erlangen‐Nürnberg Martensstrasse 7 91058 Erlangen Germany
We reveal the complex interplay between photoactive layer thickness and illumination intensity in perovskite solar cells, presenting design criteria for real-world and solar concentrator applications.
Formamidinium lead triiodide (FAPbI3) is attractive for photovoltaic devices due to its optimal bandgap at around 1.45 eV and improved thermal stability compared with methylammonium‐based perovskites. Crystallization of phase‐pure α‐FAPbI3 conventionally requires high‐temperature thermal annealing at 150 °C whilst the obtained α‐FAPbI3 is metastable at room temperature. Here, aerosol‐assisted crystallization (AAC) is reported, which converts yellow δ‐FAPbI3 into black α‐FAPbI3 at only 100 °C using precursor solutions containing only lead iodide and formamidinium iodide with no chemical additives. The obtained α‐FAPbI3 exhibits remarkably enhanced stability compared to the 150 °C annealed counterparts, in combination with improvements in film crystallinity and photoluminescence yield. Using X‐ray diffraction, X‐ray scattering, and density functional theory simulation, it is identified that relaxation of residual tensile strains, achieved through the lower annealing temperature and post‐crystallization crystal growth during AAC, is the key factor that facilitates the formation of phase‐stable α‐FAPbI3. This overcomes the strain‐induced lattice expansion that is known to cause the metastability of α‐FAPbI3. Accordingly, pure FAPbI3 p–i–n solar cells are reported, facilitated by the low‐temperature (≤100 °C) AAC processing, which demonstrates increases of both power conversion efficiency and operational stability compared to devices fabricated using 150 °C annealed films.
The charge carrier dynamics in organic solar cells and organic–inorganic hybrid metal halide perovskite solar cells, two leading technologies in thin‐film photovoltaics, are compared. The similarities and differences in charge generation, charge separation, charge transport, charge collection, and charge recombination in these two technologies are discussed, linking these back to the intrinsic material properties of organic and perovskite semiconductors, and how these factors impact on photovoltaic device performance is elucidated. In particular, the impact of exciton binding energy, charge transfer states, bimolecular recombination, charge carrier transport, sub‐bandgap tail states, and surface recombination is evaluated, and the lessons learned from transient optical and optoelectronic measurements are discussed. This perspective thus highlights the key factors limiting device performance and rationalizes similarities and differences in design requirements between organic and perovskite solar cells.
Here we report the investigation of controlled PbI2 secondary phase formation in CH3NH3PbI3 (MAPI) photovoltaics through post-deposition thermal annealing, identifying the location of PbI2 in the active layer and its beneficial role on device performance.
Recombination via subgap trap states is considered a limiting factor in the development of organometal halide perovskite solar cells. Here, the impact of active layer crystallinity on the accumulated charge and open‐circuit voltage (Voc) in solar cells based on methylammonium lead triiodide (CH3NH3PbI3, MAPI) is demonstrated. It is shown that MAPI crystallinity can be systematically tailored by modulating the stoichiometry of the precursor mix, where small quantities of excess methylammonium iodide (MAI) improve crystallinity, increasing device Voc by ≈200 mV. Using in situ differential charging and transient photovoltage measurements, charge density and charge carrier recombination lifetime are determined under operational conditions. Increased Voc is correlated to improved active layer crystallinity and a reduction in the density of trap states in MAPI. Photoluminescence spectroscopy shows that an increase in trap state density correlates with faster carrier trapping and more nonradiative recombination pathways. Fundamental insights into the origin of Voc in perovskite photovoltaics are provided and it is demonstrated why highly crystalline perovskite films are paramount for high‐performance devices.