Partha P. Mukherjee

Partha P. Mukherjee

Auto-generated profile, based on publicly available information

Partha P. Mukherjee

School of Mechanical Engineering Purdue University West Lafayette Indiana USA

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 November 2018 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
FUFrancois L. E. Usseglio-Viretta
Francois L. E. Usseglio-Viretta
Andrew M. ColclasureAndrew M. Colclasure
Andrew M. Colclasure
AMAashutosh N. Mistry
Aashutosh N. Mistry
KCKoffi Pierre Yao Claver
Koffi Pierre Yao Claver
FPFezzeh Pouraghajan
Fezzeh Pouraghajan
KSKandler Smith
Kandler Smith
Battery performance is strongly correlated with electrode microstructural properties. Of the relevant properties, the tortuosity factor of the electrolyte transport paths through microstructure pores is important as it limits battery maximum charge/discharge rate, particularly for energy-dense thick electrodes. Tortuosity factor however, is difficult to precisely measure, and thus its estimation has been debated frequently in the literature. Herein, three independent approaches have been applied to quantify the tortuosity factor of lithium-ion battery electrodes. The first approach is a microstructure model based on three-dimensional geometries from X-ray computed tomography (CT) and stochastic reconstructions enhanced with computationally generated carbon/binder domain (CBD), as CT is often unable to resolve the CBD. The second approach uses a macro-homogeneous model to fit electrochemical data at several rates, providing a separate estimation of the tortuosity factor. The third approach experimentally measures tortuosity factor via symmetric cells employing a blocking electrolyte. Comparisons have been made across the three approaches for 14 graphite and nickel-manganese-cobalt oxide electrodes. Analysis suggests that if the tortuosity factor were characterized based on the active material skeleton only, the actual tortuosities would be 1.35–1.81 times higher for calendered electrodes. Correlations are provided for varying porosity, CBD phase interfacial arrangement and solid particle morphology.

30 September 2021 in ACS Energy Letters
Verified
Journal Article
Closed access
BVBairav S. Vishnugopi
Bairav S. Vishnugopi
EKEric Kazyak
Eric Kazyak
JLJohn A. Lewis
John A. Lewis
JNJagjit Nanda
Jagjit Nanda
MMMatthew T. McDowell
Matthew T. McDowell
PMPartha P. Mukherjee
Partha P. Mukherjee

25 September 2018 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
Feng HaoFeng Hao
Feng Hao
AVAnkit Verma
Ankit Verma
PMPartha P. Mukherjee
Partha P. Mukherjee
The coupled mechanism of nonuniform Li plating and interfacial stress induced SEI instability is elucidated.

23 January 2018 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
AMAashutosh N. Mistry
Aashutosh N. Mistry
KSKandler Smith
Kandler Smith
PMPartha P. Mukherjee
Partha P. Mukherjee

7 October 2017 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
AVAnkit Verma
Ankit Verma
KSKandler Smith
Kandler Smith
SSShriram Santhanagopalan
Shriram Santhanagopalan
DADaniel Abraham
Daniel Abraham
KYKoffi Pierre Yao
Koffi Pierre Yao
PMPartha P. Mukherjee
Partha P. Mukherjee
Galvanostatic intermittent titration technique (GITT) – a popular method for characterizing kinetic and transport properties of battery electrodes – is predicated on the proper evaluation of electrode active area. LiNi0.5044Co0.1986Mn0.2970O2 (NCM523) material exhibits a complex morphology in which sub-micron primary particles aggregate to form secondary particle agglomerates. This work proposes a new active area formulation for primary/secondary particle agglomerate materials to better mimic the morphology of NCM532 electrodes. This formulation is then coupled with macro-homogeneous models to simulate GITT and half-cell performance of NCM523 electrodes. Subsequently, the model results are compared against the experimental results to refine the area formulation. A single parameter, the surface roughness factor, is proposed to mimic the change in interfacial area, diffusivity and exchange current density simultaneously and detailed modeling results are presented to provide valuable insights into the efficacy of the formulation.

5 June 2018 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
CFConner Fear
Conner Fear
DJDaniel Juarez-Robles
Daniel Juarez-Robles
JJJudith A. Jeevarajan
Judith A. Jeevarajan
PMPartha P. Mukherjee
Partha P. Mukherjee
The mechanisms driving the thermo-electrochemical response of commercial lithium-ion cells under extreme overdischarge conditions (< 0.0 V) are investigated in the context of copper dissolution from the anodic current collector. A constant current discharge with no lower cutoff voltage was used to emulate the effects of forced overdischarge, as commonly experienced by serially connected cells in an unbalanced module. Cells were overdischarged to 200% DOD (depth of discharge) at C/10 and 1C rates to develop an understanding of the overdischarge extremes. Copper dissolution began when a cell reached its minimum voltage level (between −1.3 V and −1.5 V), where the anode potential reached a maximum value of ∼4.8 V vs. Li/Li+. Deposition of copper on the cathode, anode, and separator surfaces was observed in all overdischarged cells, verified with EDS/SEM results, which further suggests the formation of internal shorts, although the cell failures proved to be relatively benign. The maximum cell surface temperature during overdischarge was found to be highly rate-dependent, with the 1C-rate cell experiencing temperatures as high as 79°C. Concentration polarization and solid electrolyte interphase (SEI) layer breakdown prior to the initiation of copper dissolution are proposed to be the main sources of heat generation during overdischarge.