Arturas Aleksandrovas

Arturas Aleksandrovas

Auto-generated profile, based on publicly available information

Arturas Aleksandrovas

Electronics Engineering Department, Kaunas University of Technology, Kaunas, LT-51368, Lithuania

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2021 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Open access
Linas SvilainisLinas Svilainis
Linas Svilainis
ACAndrius Chaziachmetovas
Andrius Chaziachmetovas
Valdas EidukynasValdas Eidukynas
Valdas Eidukynas
AAArturas Aleksandrovas
Arturas Aleksandrovas
MVMarijus Varatinskas
Marijus Varatinskas
Laser ultrasound offers several benefits in comparison to immersion or air-coupled ultrasound: it directly generates stress on the sample surface; it has a wide bandwidth and a small acoustic source can be produced. Conventionally, high-power pulsed lasers are required therefore equipment is bulky and expensive. Here we propose to use mid-power laser diodes, which are small and low cost. To solve the low signal amplitude problem with lower power lasers, the use of spread spectrum signal, arbitrary position, and width binary pulse sets is proposed. To date, a laser driver for this task has not been available. This article describes the development of such a compact driver, where the essential electronics occupy an area of $10\,\,\times20$ mm. The whole system with a fixture for kinematic mount is comparable in size to a conventional piezoelectric ultrasonic transducer. The driver can supply pulse sets of up to 40 A. Individual pulse duration can vary between 20 and 1000 ns (0.5–25-MHz ultrasound range) and the total pulse train duration is limited by the laser type used. Experiments show that up to 10- $\mu \text{s}$ long pulse sets can be used at 10-A current, without laser degradation. Current waveforms, beam profile, and optical response signals were measured for three rectified topologies. It was concluded that the GaN-based constant current switch topology has the best performance, but a power MOSFET in a source current feedback topology can also be used to generate pulses down to 20 ns. Photoacoustic response signals from chirp and phase shift keying modulation have been demonstrated.

30 December 2021 in IEEE Access
Verified
Journal Article
Open access
ARAlberto Rodríguez
Alberto Rodríguez
Linas SvilainisLinas Svilainis
Linas Svilainis
MLMiguel Ángel de la Casa Lillo
Miguel Ángel de la Casa Lillo
TATomas Gomez Alvarez-Arenas
Tomas Gomez Alvarez-Arenas
AAA. Aleksandrovas
A. Aleksandrovas
ASA. Salazar
A. Salazar
This work presents in detail a new method for the optimization of rectangular spread spectrum excitation signals for its use in simple and low-cost ultrasonic pulsers, but that could be extended to other applications based on spread spectrum signals. Starting from rectangular linear frequency modulated (RLFM) chirps, it uses the transfer function of the transmitted signal and received echoes from reference specimens to iterate through a recursive algorithm to obtain arbitrary position and width pulse (APWP) signals with the desired bandwidth, maximizing the energy and the flatness of the spectrum, and enhancing the resolution and dynamic range of conventional chirp excitation signals. This optimization procedure can be repeated for any transducer and material, so that it achieves the best performance in each experimental environment. Such characteristics are ideal for Time-of-Flight estimation, imaging, and applications in which spectral regularity is needed, such as the Split Spectrum Processing (SSP) algorithm, which is used as example to test the performance of the proposed excitation signals. It also allows to specify and change the bandwidth reducing the need to change the transducers. The method is tested with different transducers (2 and 5 MHz focused transducers) and complex composite materials (aluminum-carbon aviation composite and high porosity GFRP composite) in immersion setup for imaging applications using SSP algorithm.

19 December 2016 in Elektronika ir Elektrotechnika
Verified
Journal Article
Open access
PDF file
AAArturas Aleksandrovas
Arturas Aleksandrovas
ARAlberto Rodríguez
Alberto Rodríguez
Linas SvilainisLinas Svilainis
Linas Svilainis
MLMiguel Ángel de la Casa Lillo
Miguel Ángel de la Casa Lillo
ASAddisson Salazar
Addisson Salazar
Ultrasound-Based Density Estimation of Composites Using Water-Air Interface