15 January 2025 in Nature
18 September 2024 in Nature Energy
The interlaboratory comparability and reproducibility of all-solid-state battery cell cycling performance are poorly understood due to the lack of standardized set-ups and assembly parameters. This study quantifies the extent of this variability by providing commercially sourced battery materials—LiNi0.6Mn0.2Co0.2O2 for the positive electrode, Li6PS5Cl as the solid electrolyte and indium for the negative electrode—to 21 research groups. Each group was asked to use their own cell assembly protocol but follow a specific electrochemical protocol. The results show large variability in assembly and electrochemical performance, including differences in processing pressures, pressing durations and In-to-Li ratios. Despite this, an initial open circuit voltage of 2.5 and 2.7 V vs Li+/Li is a good predictor of successful cycling for cells using these electroactive materials. We suggest a set of parameters for reporting all-solid-state battery cycling results and advocate for reporting data in triplicate.
4 December 2022 in Advanced Materials Interfaces
Lithium‐thiophosphate‐based all‐solid‐state batteries (ASSBs) are increasingly attracting attention for high‐density electrochemical energy storage. In this work, the cycling performance of single and polycrystalline forms of LiNixCoyMnzO2 (NCM, with ≥83% Ni content) cathode active materials in ASSB cells with an Li4Ti5O12 composite anode is explored, and the advantages and disadvantages of both morphologies are discussed. The virtual lack of grain boundaries in the quasi‐single‐crystalline material is found to contribute to improved stability by eliminating the tendency of Ni‐rich NCM particles to crack during cycling, due to volume differences between the lithiated and delithiated phases. Although the higher crack resistance mitigates effects of chemical oxidation of the lithium thiophosphate solid electrolyte, the cells suffer from electrochemical side reactions occurring at the cathode interfaces. However, coating the single‐crystal particles with a protective LiNbO3 overlayer helps to stabilize the interface between cathode active material and solid electrolyte, leading to a capacity retention of 93% after 200 cycles (with qdis ≈ 160 mAh gNCM−1 or 1.7 mAh cm−2 at C/5 rate and 45 °C). Overall, this work highlights the importance of addressing electro‐chemo‐mechanical phenomena in ASSB electrodes.
10 March 2023 in Chemical Communications
TEM investigations under cryogenic conditions reveal transition-metal dissolution and interdiffusion into the bulk solid electrolyte in thiophosphate-based all-solid-state batteries.
15 August 2023 in Chemistry of Materials
19 May 2023 in Journal of Physics: Energy
Sodium-ion batteries (SIBs) see intensive research and commercialization efforts, aiming to establish them as an alternative to lithium-ion batteries. Among the reported cathode material families for SIBs, Na-deficient P2-type layered oxides are promising candidates, benefiting from fast sodium diffusion and therefore high charge/discharge rates. However, upon sodium extraction at high potentials, a transition from the P2 to O2 phase occurs, with the corresponding change in cell volume resulting in particle fracture and capacity degradation. A possible solution to this is to increase configurational entropy by introducing more elements into the transition-metal layer (so-called high-entropy concept), leading to some kind of structural stabilization. In this work, the acoustic emission (AE) of a series of P2-type layered oxide cathodes with increasing configurational entropy [Na0.67(Mn0.55Ni0.21Co0.24)O2, Na0.67(Mn0.45Ni0.18Co0.24Ti0.1Mg0.03)O2 and Na0.67(Mn0.45Ni0.18Co0.18Ti0.1Mg0.03Al0.04Fe0.02)O2] is recorded during SIB operation and correlated to the materials properties, namely change in c lattice parameter and cracking behavior. A structure-property relationship between entropy, manifested in the extent of phase transition, and detected AE is derived, supported by the classification of signals by peak frequency. This classification in combination with microscopy imaging allows to distinguish between inter- and intragranular fracture. Relatively more intergranular and less intragranular crack formation is observed with increasing configurational entropy.