Shutao Song

Shutao Song

Auto-generated profile, based on publicly available information

Shutao Song

Department of Mechanical and Aerospace Engineering, University of Central Florida, Orlando, FL, USA

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2021 in Acta Materialia
Verified
Journal Article
Open access
HHHolden Hyer
Holden Hyer
LZLe Zhou
Le Zhou
AMAbhishek Mehta
Abhishek Mehta
SPSharon Park
Sharon Park
THThinh Huynh
Thinh Huynh
Yongho SohnYongho Sohn
Yongho Sohn

1 May 2021 in Materialia
Verified
Journal Article
Closed access
HHHolden Hyer
Holden Hyer
LZLe Zhou
Le Zhou
QLQingyang Liu
Qingyang Liu
DWDazhong Wu
Dazhong Wu
SSShutao Song
Shutao Song
YSYongho Sohn
Yongho Sohn

12 November 2020 in Composite Interfaces
Verified
Journal Article
Closed access
SSShutao Song
Shutao Song
MBMuktadir Billah
Muktadir Billah
QZQiang Zhou
Qiang Zhou
LRLuyang Ren
Luyang Ren
LZLiangfu Zheng
Liangfu Zheng
Yuanli BaiYuanli Bai
Yuanli Bai
The mechanical strength of pure aluminum matrix can be greatly enhanced by adding a small amount of nickel-coated carbon nanotubes (NiCNTs), where the nickel coating helps to the uniform dispersion of carbon nanotubes (CNTs) within the aluminum matrix through decreasing density difference and avoiding CNTs agglomeration. The yield strength of pure aluminum can be increased by 33.3% with 1% weight fraction of NiCNTs. This strengthening effect is caused by three mechanisms: Orowan looping, load bearing, and thermal expansion mismatch which are studied by both finite-element method and analytical method. A series of finite-element analyses using a representative volume element (RVE) method are conducted considering influences of CNTs aspect ratios, volume fraction of hardened zone, and the hardened plastic strain of hardened zone. The results show that the aspect ratio of CNTs is very important in the strengthening of CNT-reinforced composites, and the yield stress increases with increasing aspect ratio. A set of parameters for analytical solutions are optimized that can well describe and accurately predict the experimental data. Both the finite-element analysis and analytical solution are well correlated with the experimental results for Al/NiCNT composites with different weight fractions of CNTs. Graphical Abstract

1 October 2020 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
QZQiang Zhou
Qiang Zhou
SSShutao Song
Shutao Song
QCQuanfang Chen
Quanfang Chen
Yuanli BaiYuanli Bai
Yuanli Bai
Aluminum powder compaction was studied using both test and simulation. Cold compaction, hot compaction, and vibration-assisted (cold) compaction tests were conducted to achieve different density ratios. First, the hot compaction test (at 300 °C, compression pressure 140 MPa) improved about 6% compared with cold compaction under the same compression pressure. Second, although the relative density ratio does not obviously improve at a vibration-assisted (cold) compaction, the strength of the specimens made under vibration loading is much better than those of cold compaction. Additionally, finite element models with well-calibrated Drucker–Prager Cap (DPC) material constitutive model were built in abaqus/standard to simulate the powder compaction process. The results of the finite element model have very good correlations with test results up to the tested range, and this finite element model further predicts the loading conditions needed to achieve the higher density ratios. Two exponential equations of the predicted density ratio were obtained by combining the test data and the simulation results. A new analytical solution was developed to predict the axial pressure versus the density ratio for the powder compaction according to DPC material model. The results between the analytical solution and the simulation model have a very good match.