7 June 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The fight against global climate change demands the electrification of aircraft propulsion. One of the most significant and distinct challenges that future multi-megawatt electrified propulsion will face is high voltage at high altitudes, which could cause significant partial discharge and reduce the reliability of the propulsion system. Recognizing this challenge, a multi-disciplinary research team has proposed, designed, built, and preliminarily tested a 2-kV 1-MW 20,000 RPM integrated modular motor drive (IMMD) with an unprecedented weight power density of 9 kW/kg. This paper presents the architecture, major design approaches, test results of associated power electronics systems at the rated voltage and current, and preliminary test results of the full IMMD prototype. Full power and system-level altitude tests of the IMMD are already planned at the National Aeronautics and Space Administration (NASA’s) test facility.
2 November 2021 in IEEE Transactions on Transportation Electrification
Partial discharge (PD) is a major cause of degradation of motor winding insulation. It is a challenge to the successful electrification of all types of ground, sea, and aerial vehicles. However, the mechanism of PD under pulsewidth modulated voltages is not fully understood. This article studies PD inception characteristics in twisted pairs under single voltage pulses with reduced voltage overshoot, aiming to study the PD inception characteristics and mechanism without the influences of memory effects and voltage overshoot. The tests are conducted with a lab-designed 10-kV silicon carbide (SiC) device-based voltage pulse generator. The generator can produce voltage pulses with variable rise/fall times and pulse widths to emulate the output voltages of both silicon (Si) and SiC device-based power electronics converters. The voltage overshoot in this study has been limited to less than 5%. In addition, single voltage pulses are utilized as the excitation to remove charge memory effects. PD inception voltages, PD current magnitudes, and PD time delays of twisted pair samples are measured under various test conditions. It is found that the partial discharge inception voltage (PDIV) of the test sample decreases with reduced voltage rise time and increased voltage pulsewidth. Based on the test results, the impacts of voltage rise/fall times and pulse widths on PD behavior are explained using the extended volume-time theory. The relationships between PDIV, voltage rise/fall time, and pulsewidth are presented through empirical equations. Test results and analysis provide insights on the impacts of emerging wide bandgap devices in applications on motor winding insulations.
1 September 2018 in Physics of Plasmas
Polyetheretherketone is used in the packaging of high voltage power electronics as a frame material, and the surface discharge behaviors of polyetheretherketone are the main concerns for the packaging design. Pulse width modulation voltage, which shows a variable duty cycle, is applied to polyetheretherketone at working conditions. The surface discharge behaviors of polyetheretherketone under a positive repetitive pulse voltage of 50 Hz with different duty cycles were investigated in this paper. It is generally considered that the surface discharge inception is mainly related to electric field distribution; however, the pulse width of voltage could significantly affect the surface discharge inception characteristics. In this study, the surface discharge inception voltage, time-integrated streamer images, and cumulative surface discharge patterns under a positive repetitive pulse voltage of 50 Hz were obtained. It was found that the surface discharge inception voltage decreased with the increase in the duty cycle. This relationship was explained by the role of time-lag. Time-lag distribution analysis was performed, and the time-lag distribution was mainly determined by stochastic time-lag. The mean stochastic time-lag was obtained by the Laue plot, and the relationship between the mean stochastic time-lag and applied voltage could be well fitted by the inverse power law. Furthermore, the relationship between the surface discharge inception voltage and duty cycle could be exactly fitted by the inverse power law, which was derived from the relationship between the stochastic mean time-lag and applied voltage. The closely related relationships demonstrate that time-lag plays a critical role in the surface discharge inception at different duty cycles.
1 January 2019 in IET Power Electronics
Electrical insulation capability is one of the most critical challenges for press‐pack insulated gate bipolar transistors (IGBTs), but the knowledge of its insulation failure mechanism is much less mature. To understand the insulation failure mechanism, partial discharge (PD) measurement and analysis in press‐pack IGBT (PPI) submodule were performed in this study. A dedicated PD measurement system for PPIs was designed and fabricated, and fast oscilloscope, PD detector and ultraviolet (UV) image camera were employed to observe the PD. PD‐induced insulation failure phenomenon in the submodule was observed under direct current voltage, and UV images indicated that the discharge occurred at the periphery of the die. Phase‐resolved PD (PRPD) analysis method for PPIs was developed and three elementary structures were used to simulate the PD in the electric field reinforcement areas identified by electric field analysis. According to PRPD patterns, the observed PD in the submodule was considered to be mainly caused by a mismatch between the electric field and critical electric field on the surface of passivation layers of the die. The inference was verified at different gas pressures because a decrease of PD inception voltage in the submodule and the bare die was observed at lower gas pressure.
25 December 2023 in IEEE Transactions on Power Electronics
This research introduces a unique bidirectional dc–dc converter specifically developed for energy storage applications. The proposed circuit topology exhibits a high voltage conversion ratio and a reduced current ripple. On the transformer primary side, a quasi-switched-capacitor (QSC) circuit mitigates voltage stress on switching devices and achieves a 3:1 voltage step-down ratio. The proposed transformer-interleaved circuit on the secondary side features the 2:1 voltage conversion ratio and minimizes the battery current ripple without adding extra switching or magnetic components. The 6:1 voltage conversion contributes to a simpler winding structure, smaller transformer size, and lower transformer loss in high voltage gain application. Furthermore, the reduced current ripple leads to lower battery heat generation and smaller filter bank capacitance, making it suitable for high-density design. The implementation of phase shift control, similar to the dual-active-bridge circuit, serves to regulate the circuit's transferred power. A 1-kW, 300-kHz, 380–420-/20–33-V GaN-based circuit prototype is developed and tested. The tested peak efficiency is 98.5% with a power density of 30.42 W/in 3 .
1 December 2020 in High Voltage
In this study, the surface discharge current pulses of polyetheretherketone (PEEK) material under positive repetitive square voltage in a nitrogen atmosphere are measured. The influences of different voltage amplitudes and frequencies on the detail parameters of forward discharge and backward discharge current pulses are statistically analysed. The results show that as the square voltage amplitude increases, the current pulse amplitude, fall time and pulse width of both forward and backward discharge current increase, and the rise time does not change significantly. As the voltage frequency increases, current pulse amplitude, fall time and pulse width of both forward and backward discharge current decrease, and the rise time does not change significantly. Due to the independence of the discharge at different repetitive cycles, the specific discharge process in one cycle is analysed in detail to explain the influence mechanism of the voltage amplitude and frequency on the discharge current. By mean of the Richardson–Schottky and the Cavallini relaxation model, the relationship between discharge voltage ratio and surface charge, and the decay process of surface discharge are analysed. Furthermore, the influences of amplitude and frequency of the positive repetitive square voltage on the PEEK surface current pulses are explained qualitatively.