A small array of single photon avalanche detectors (SPADs) has been designed and fabricated in a standard 0.18 μm CMOS process to test a new photon detecting system for optical communications. First numerical results are presented which show that using arrays of SPADs reduces the optical power density required at the receiver. Experimental results then show that the new system preserves the photon counting ability of the SPADs. Finally a simple method is presented which can be used to estimate the size of array needed to achieve a particular target bit error rate at a specific optical power density. Together these results indicate that by replacing the avalanche photodiode in a receiver with the new system it will be possible to count the received photons.
16 November 2011 in IEEE Photonics Technology Letters
A single-pixel plasmonic complementary metal oxide semiconductor (CMOS) photo sensor consisting of a plasmonic color filter integrated on a CMOS photodiode was fabricated using electron beam lithography and dry etch. The photocurrent measurement results confirmed the three primary color filtering responses that could be achieved in a single layer of nanostructured aluminium film. Finite-difference time-domain simulation demonstrated a good agreement of the reflection spectra with the measured result. This research can lead to the development of advanced CMOS image sensors with low cost and low crosstalk.
28 February 2018 in Journal of Lightwave Technology
Visible light communications is an alternative method of indoor wireless communications that requires sensitive receivers. Ideally, single photon avalanche detectors (SPADs) could be used to create more sensitive receivers. However, the dead time, finite output pulse width, and photon detection efficiency of existing SPAD arrays limit their sensitivity and bandwidth. In this paper, an accurate equation for the impact of dead time on the sensitivity of a SPAD array is presented. In addition, the impact of the width of the output pulses on the on-off keying data rate is investigated. Finally, a comparison between receivers containing an avalanche photo-diode (APD) and a large array of SPADs shows that although the receiver containing the SPAD is more sensitive in the dark, the APD-based receiver is more sensitive in a normal operating condition. However, the models that predict the performance of both receivers suggest that newer SPAD arrays will enable significant improvements in receiver sensitivity.
We present the first three-dimensional, functional images of the human brain to be obtained using a fibre-less, high-density diffuse optical tomography system. Our technology consists of independent, miniaturized, silicone-encapsulated DOT modules that can be placed directly on the scalp. Four of these modules were arranged to provide up to 128, dual-wavelength measurement channels over a scalp area of approximately 60 × 65 mm2. Using a series of motor-cortex stimulation experiments, we demonstrate that this system can obtain high-quality, continuous-wave measurements at source-detector separations ranging from 14 to 55 mm in adults, in the presence of hair. We identify robust haemodynamic response functions in 5 out of 5 subjects, and present diffuse optical tomography images that depict functional haemodynamic responses that are well-localized in all three dimensions at both the individual and group levels. This prototype modular system paves the way for a new generation of wearable, wireless, high-density optical neuroimaging technologies.
The first wearable multi-wavelength technology for functional near-infrared spectroscopy has been developed, based on a custom-built 8-wavelength light emitting diode (LED) source. A lightweight fibreless probe is designed to monitor changes in the concentrations of multiple absorbers (chromophores) in biological tissue, the most dominant of which at near-infrared wavelengths are oxyhemoglobin and deoxyhemoglobin. The use of multiple wavelengths enables signals due to the less dominant chromophores to be more easily distinguished from those due to hemoglobin and thus provides more complete and accurate information about tissue oxygenation, hemodynamics, and metabolism. The spectroscopic probe employs four photodiode detectors coupled to a four-channel charge-to-digital converter which includes a charge integration amplifier and an analogue-to-digital converter (ADC). Use of two parallel charge integrators per detector enables one to accumulate charge while the other is being read out by the ADC, thus facilitating continuous operation without dead time. The detector system has a dynamic range of about 80 dB. The customized source consists of eight LED dies attached to a 2 mm × 2 mm substrate and encapsulated in UV-cured epoxy resin. Switching between dies is performed every 20 ms, synchronized to the detector integration period to within 100 ns. The spectroscopic probe has been designed to be fully compatible with simultaneous electroencephalography measurements. Results are presented from measurements on a phantom and a functional brain activation study on an adult volunteer, and the performance of the spectroscopic probe is shown to be very similar to that of a benchtop broadband spectroscopy system. The multi-wavelength capabilities and portability of this spectroscopic probe will create significant opportunities for in vivo studies in a range of clinical and life science applications.