Joshua Fernandez

Joshua Fernandez

Auto-generated profile, based on publicly available information

Joshua Fernandez

Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA, USA

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 November 2023 in IEEE Transactions on Medical Robotics and Bionics
Verified
Journal Article
Closed access
CNChristoph Nuesslein
Christoph Nuesslein
KBKrishan Bhakta
Krishan Bhakta
JFJoshua Fernandez
Joshua Fernandez
FDFelicia Davenport
Felicia Davenport
Jennifer LeestmaJennifer Leestma
Jennifer Leestma
AYAaron Young
Aaron Young
Performing heavy manual lifting jobs can be extremely strenuous, often resulting in high rates of injury at overloaded joints. Lower-body exoskeletons have potential to mitigate this fatigue and injury through targeted joint assistance. A variety of current wearable devices aim to provide this kind of support, but their effects on both directly and indirectly targeted joints have not been fully investigated. In this study, a powered bilateral knee exoskeleton (research device), and passive back exosuit (HeroWear Apex) were compared across 10 individuals through a battery of manual lifting tasks. Metabolic, electromyographic, and subject-reported outcome measure data were used to determine which exoskeleton provided the best assistance for each task type. It was found that the knee exoskeleton significantly reduced metabolic cost by 9.6% compared to the no-exoskeleton baseline (p<.05). Both the knee and back exoskeletons reduced activation in up to 6 of the muscles measured (out of 16). Importantly, each device primarily reduced muscle activation around the joint it targeted, not around adjacent joints. These findings suggest that exoskeletons that target the knee or lower back joint during lifting can provide significant assistance in reducing exertion.

4 February 2021 in IEEE Robotics and Automation Letters
Verified
Journal Article
Closed access
JFJoshua Fernandez
Joshua Fernandez
AMAnirban Mazumdar
Anirban Mazumdar
Granular media, like sand, restricts vehicle traction and degrades the ability of mobile robots to pull loads. Solutions that are effective on hard or clean surfaces fail on sand. This work presents a mobile robot system that utilizes an active tail to greatly increase its ability to pull loads. The robot combines dynamic tail impacts, plowing, and leveraging of cable tension to achieve this improved performance. The key contributions of this letter are 1) illustrating how dynamic impacts can provide substantial anchoring force on two terrain types, 2) incorporating anchoring behavior into tail actuator design, 3) combining tail and wheel behaviors to create granular barriers, 4) leveraging geometry to utilize winch tension for enhanced performance, and 5) experimentally demonstrating the ability to transport loads 6x the robot mass on a deep sandy surface. The prototype 7.6 kg robot was able to pull a 45.5 kg load on a deep sand surface. This is a substantial improvement over the baseline robot which was only able to pull a 13.6 kg load.

1 April 2025 in Journal of Applied Biomechanics
Verified
Journal Article
Open access
PDF file
FDFelicia R. Davenport
Felicia R. Davenport
Jennifer LeestmaJennifer Leestma
Jennifer Leestma
ASAdriana Staten
Adriana Staten
KBKrishan Bhakta
Krishan Bhakta
JFJoshua Fernandez
Joshua Fernandez
GSGregory S. Sawicki
Gregory S. Sawicki
Repetitive manual labor tasks involving twisting, bending, and lifting commonly lead to lower back and knee injuries in the workplace. To identify tasks with high injury risk, we recruited N = 9 participants to perform industry-relevant, 2-handed lifts with a 11-kg weight. These included symmetrical/asymmetrical, ascending/descending lifts that varied in start-to-end heights (knee-to-waist and waist-to-shoulder). We used a data-driven musculoskeletal model that combined force and motion data with a muscle activation-informed solver (OpenSim, CEINMS) to estimate 3-dimensional internal joint contact forces (JCFs) in the lower back (L5/S1) and knee. Symmetrical lifting resulted in larger peak JCFs than asymmetrical lifting in both the L5/S1 (+20.2% normal [P < .01], +20.3% shear [P = .001], +20.6% total [P < .01]) and the knee (+39.2% shear [P = .001]), and there were no differences in peak JCFs between ascending versus descending motions. Below-the-waist lifting generated significantly greater JCFs in the L5/S1 and knee than above-the-waist lifts (P < .01). We found a positive correlation between knee and L5/S1 peak total JCFs (R2 = .60, P < .01) across the task space, suggesting motor coordination that favors sharing of load distribution across the trunk and legs during lifting.