Michele Carrabba

Michele Carrabba

Auto-generated profile, based on publicly available information

Michele Carrabba

Department of Medical Biotechnologies, University of Siena, Siena, Italy

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2017 in Journal of Dentistry
Verified
Journal Article
Open access
MCMichele Carrabba
Michele Carrabba
AKAndrew J. Keeling
Andrew J. Keeling
AAAziz Aziz
Aziz Aziz
AVAlessandro Vichi
Alessandro Vichi
RFRiccardo Fabian Fonzar
Riccardo Fabian Fonzar
Marco FerrariMarco Ferrari
Marco Ferrari
To compare three different compositions of Yttria-Tetragonal Zirconia Polycrystal (Y-TZP) ceramic and a lithium disilicate ceramic in terms of flexural strength and translucency. Three zirconia materials of different composition and translucency, Aadva ST [ST], Aadva EI [EI] and Aadva NT [NT](GC Tech, Leuven, Belgium) were cut with a slow speed diamond saw into beams and tabs in order to obtain, after sintering, dimensions of 1.2×4.0×15.0mm and 15.0×15.0×1.0mm respectively. Blocks of IPS e.max CAD LT were cut and crystallized in the same shapes and dimensions and used as a reference group [LD]. Beams (n=15) were tested in a universal testing machine for three-point bending strength. Critical fracture load was recorded in N, flexural strength (σ in MPa), Weibull modulus (m) and Weibull characteristic strength (σ0 in MPa) were then calculated. Tabs (n=10) were measured with a spectrophotometer equipped with an integrating sphere. Contrast Ratios were calculated as CR=Yb/Yw. SEM of thermally etched samples coupled with lineal line analysis (n=6) was used to measure the tested zirconia grain size. Data were statistically analyzed. Differences in translucency, flexural strength and grain size were found to be statistically significant. CR increased and flexural strength decreased in the following order ST(σ 1215±190MPa, CR 0.74±0.01)>EI(σ 983±182MPa, CR 0.69±0.01)>NT(σ 539±66MPa, CR 0.65±0.01)>LD (σ 377±39Mpa, CR 0.56±0.02). The average grain size was different for the three zirconia samples with NT(558±38nm)>ST(445±34nm)>EI(284±11nm). The zirconia composition heavily influenced both the flexural strength and the translucency. Different percentages of Yittria and Alumina result in new materials with intermediate properties in between the conventional zirconia and lithium disilicate. Clinical indications for Zirconia Aadva NT should be limited up to three-unit span bridges.

29 June 2014 in Journal of Esthetic and Restorative Dentistry
Verified
Journal Article
Closed access
PDF file
Alessandro VichiAlessandro Vichi
Alessandro Vichi
MCMichele Carrabba
Michele Carrabba
RPRade Paravina
Rade Paravina
Marco FerrariMarco Ferrari
Marco Ferrari

1 January 2017 in Dental Materials
Verified
Journal Article
Closed access
RFRiccardo Fabian Fonzar
Riccardo Fabian Fonzar
MCMichele Carrabba
Michele Carrabba
MSMaurizio Sedda
Maurizio Sedda
Marco FerrariMarco Ferrari
Marco Ferrari
Cecilia GoracciCecilia Goracci
Cecilia Goracci
Alessandro VichiAlessandro Vichi
Alessandro Vichi

17 November 2015 in Journal of Esthetic and Restorative Dentistry
Verified
Journal Article
Closed access
PDF file
Alessandro VichiAlessandro Vichi
Alessandro Vichi
MSMaurizio Sedda
Maurizio Sedda
RFRiccardo Fabian Fonzar
Riccardo Fabian Fonzar
MCMichele Carrabba
Michele Carrabba
Marco FerrariMarco Ferrari
Marco Ferrari

1 July 2015 in The Journal of Prosthetic Dentistry
Verified
Journal Article
Closed access
MSMaurizio Sedda
Maurizio Sedda
AVAlessandro Vichi
Alessandro Vichi
MCMichele Carrabba
Michele Carrabba
ACAlessandro Capperucci
Alessandro Capperucci
CLChris Louca
Chris Louca
Marco FerrariMarco Ferrari
Marco Ferrari

1 March 2017 in Operative Dentistry
Verified
Journal Article
Closed access
MCM Carrabba
M Carrabba
AVA Vichi
A Vichi
GVG Vultaggio
G Vultaggio
SPS Pallari
S Pallari
RPR Paravina
R Paravina
Marco FerrariMarco Ferrari
Marco Ferrari
SUMMARY: Objectives: To evaluate surface roughness and gloss of feldspathic ceramic blocks for chairside CAD/CAM systems before and after finishing and polishing.Methods: VITA Mark II ceramic blocks for the CEREC CAD/CAM system were cut perpendicularly in order to obtain a total of 70 specimens (14 × 18 × 3 mm). The flat surface was roughened using a grinder/polisher with dry 120-grit silicone-carbide paper. Surface roughness and gloss were measured using a digital profilometer (Ra) and a glossmeter (GU), respectively. Specimens were randomly divided into seven groups (n=10) based on the finishing/polishing system as follows: 1) Identoflex NGPorcelain Polisher (INP), 2) Identoflex Diamond Ceramic Polisher (IDP), 3) Hiluster Polishing System (HPS), 4) OptraFine (OF), 5) Identoflex Lucent (IL), 6) VITA Akzent Glaze Spray (AGS), and 7) VITA Shading Paste and Liquid (SPL). Surface analysis was repeated after the finishing/polishing treatment, and the obtained data were compared to the baseline in order to evaluate the ΔRa and ΔGU. Results were statistically analyzed. The surface morphology was observed by scanning electron microscopy.Results: The mean surface roughness of polished systems increased in the order (statistical groups designated) SPLa < ILa < OFab < IDPbc < AGSbc < INPbc < HPSc and mean gloss decreased in the order AGSa > SPLa > OFab > ILabc > HPSbcd > INPcd > IDPd.Conclusions: The smoothest surface of CAD/CAM feldspathic ceramic blocks was achieved using the furnace-based glaze systems VITA Akzent Glaze Spray and VITA Shading Paste and Liquid and manual systems Identoflex Lucent and OptraFine.