Fatih Zungor

Fatih Zungor

Auto-generated profile, based on publicly available information

Fatih Zungor

Mamur Technology Systems Inc. Istanbul Turkiye

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2023 in IEEE Access
Verified
Journal Article
Open access
FZFatih Zungor
Fatih Zungor
HBHaci Bodur
Haci Bodur
MÖMetin Öztürk
Metin Öztürk
AOAtiye Hulya Obdan
Atiye Hulya Obdan
Induction heating is a commonly used method of heating in household appliances due to its efficiency and high reliability reasons. In induction cookers, resonant inverter circuits are frequently chosen due to their high efficiency and the ability to facilitate soft switching. Among the resonant inverters used in induction cookers, half-bridge series resonant (HBSR) inverter topology is often preferred for applications where a balance between cost and power is required. Despite the numerous circuit designs proposed to enhance the performance of HBSR converters, a standardized design methodology suitable for circuit design dedicated to induction cookers has not yet been established. In this study, a new HBSR inverter design methodology supported by various theoretical equations is proposed for use in household induction cooktops. In the proposed design, the first step involves calculating the equivalent resistance value of the coil. Subsequently, a coil capable of achieving to match this resistance value is designed mechanically. Finally, the capacitance value for the resonance circuit is calculated. Calculating the equivalent resistance value before designing the coil, in particular, enables the practical implementation of a viable coil design. To validate the proposed design methodology, it is necessary to control the power transferred to the resonant circuit. For this purpose, closed-loop power control is achieved using the peak value of coil current through frequency modulation technique. Additionally, it needs to be also proved that the implementation circuit works with soft switching between maximum and minimum switch cut-off current. To assess the compliance of the proposed design method with standards, thermal measurements were taken from semiconductors, EMC measurements were conducted to verify compliance with the IEC 55014-1 standard, and finally, the power transferred to the resonant circuit was calculated using oscilloscope measurements. Using the proposed design method, calculations were performed for a 20cm diameter iron pot with a 2300VA power transfer at 230VAC mains voltage. Subsequently, these calculations were verified using various simulation tools, and finally, a prototype implementation circuit was realized to demonstrate the reliability of the proposed design method.

27 February 2026 in International Journal of Circuit Theory and Applications
Verified
Journal Article
Closed access
OGOnur Gonullu
Onur Gonullu
SSSeref Can Seyrek
Seref Can Seyrek
MÖMetin Öztürk
Metin Öztürk
FKFirat Kacar
Firat Kacar
FZFatih Zungor
Fatih Zungor
DEDurmuş ERSOY
Durmuş ERSOY

27 October 2021
Verified
Conference Paper
Closed access
FZFatih Zungor
Fatih Zungor
MBM. Faruk Bilicioglu
M. Faruk Bilicioglu
EKEnes Kavak
Enes Kavak
IEIbrahim Eski
Ibrahim Eski
MÖMetin Öztürk
Metin Öztürk
HBHaci Bodur
Haci Bodur
Among the converters used in welding machines, two-switch forward converter has an important place in low and medium power applications for cost priority applications. However, one of the most important disadvantage of this converter is limited duty cycle, which is less than 50%. Therefore, the capacitors used for shaping the main line voltage occupy an important place on the circuit. Another disadvantage of the converter is that the transformer uses the B-H curve unidirectional way. This causes the transformer to be selected larger when compared to other converters for the same power value. In this study, it has been suggested use forward converter with active clamp to which provides using the B-H curve bidirectional way with clamp capacitor, extending duty cycle more than %50 and increasing power density solve these disadvantages of two switch forward converter for welding machines. For this purpose, a converter with 230V input; 25V/150A and 3750W output will be designed and simulated to show that the converter solves the mentioned disadvantages.