A critical component for all high-power laser systems that is particularly susceptible to laser damage is the antireflective coating, which maximizes energy transmission and minimizes scattered and stray light. We demonstrate the ability to generate substrate-engraved nanostructured surfaces (NS) for scalable and designable antireflective (AR) coatings that are monolithic to the substrate and can handle peak power levels comparable to the bulk material. Experimentally measured reflectance from these fabricated structures has validated our effective index theory-based transmission matrix model, demonstrating the designability of the AR properties. Upon exposure to sufficiently high fluences, a new mode of damage, nanostructured surface damage, has been observed and is likely the result of thermally driven material reflow accompanied by plasma initiation on the nanostructured surface. At 1053 nm, nanostructured surface damage onsets at with sample cleaning and after laser conditioning—very close to the reference substrate at . At 351 nm we show damage onset of , with reference substrate material damage onset of . Therefore, damage is close to the bulk material and represents an improvement with respect to other methods. The nanostructured surfaces were found to be mechanically durable and able to withstand cleaning procedures with sonication. Under normal incidence mechanical testing with a 200 µm radius indenter tip, the AR performance of these nanostructured surfaces was minimally impacted at pressures orders of magnitude higher than an average fingerprint pressure—indicating that incidental handling contact will not affect NS structures. Mechanical damage is attributed to plastic compression, not fracturing of the NS features. We demonstrate for the first time, to the best of our knowledge, that NS AR coatings, despite being rich in etched surface features, can tolerate laser fluences comparable to unprocessed optical surfaces. Furthermore, laser-damage features of NS indicate a unique non-growing failure mode whereby following absorption the featureless damage site does not precipitate future damage growth, reducing considerably the burdens for managing optics processing in high-power laser systems.
High intensity and high energy laser facilities place increasing demands on optical components, requiring large surface area optics with exacting specifications. Petawatt lasers are high energy, short-pulse laser systems generally based on chirped-pulse amplification, where an initial low energy short pulse is stretched, amplified, and then recompressed to produce fs to ps high-power laser pulses. In such petawatt lasers, the highest demands are placed on the final optics, including gratings which compress the pulses and mirrors which direct and focus the final high-power beams. The limiting factor in these optical components is generally laser-induced damage. Designing and fabricating these optical components to meet reflection, dispersion, and other requirements while meeting laser-induced damage requirements is the primary challenge discussed in this tutorial. We will introduce the reader to the technical challenges and tradeoffs required to produce mirrors for petawatt lasers and discuss current research directions.
Active metasurfaces designed to operate at optical frequencies are flat optical elements that can dynamic, subwavelength‐scale wavefront control of reflected or transmitted light. The practical and fundamental power‐handling limits of active metasurfaces at high pulse energies and high average powers determine the potential applications for these emerging photonic components. Here, we investigate thermal performance limits of reflective gate‐tunable conducting oxide metasurfaces illuminated with high power density laser beams, for both continuous wave (CW) and pulsed laser illumination. Our gate‐tunable metasurfaces use indium tin oxide (ITO) as an active material, which undergoes an epsilon‐near‐zero (ENZ) transition under applied electrical bias. We experimentally show that under CW illumination, there is no significant change in the electrically tunable metasurface optical response for high irradiances ranging from 1.6 kW/cm 2 to 9.1 kW/cm 2 when the illuminating laser beam diameter is 7 μm. Even under an applied bias, when over 60% of the incoming light is absorbed in a 1 nm–thick charge accumulation layer within ITO, the local temperature rise in the metasurface is modest, supporting its robustness for high‐power applications. Additionally, we theoretically show that in the ENZ regime, the metasurface reflectance can be increased by a factor of 10 by replacing the active ITO layer with cadmium oxide (CdO). Thus conducting oxide metasurfaces can tolerate the power densities needed in higher power applications, including free space optical communications, to light detection and ranging (LiDAR), as well as laser‐based additive manufacturing.