MXenes are a family of two-dimensional nanomaterials. Titanium carbide MXene (Ti3C2Tx-MXene), reported in 2011, is the first inorganic compound reported among the MXene family. In the present work, we report on the study of the composition and various physical properties of Ti3C2Tx-MXene nanomaterial, as well as their temperature evolution, to consider MXenes for space applications. X-ray diffraction, thermal analysis and mass spectroscopy measurements confirmed the structure and terminating groups of the MXene surface, revealing a predominant single OH layer character. The temperature dependence of the specific heat shows a Debye-like character in the measured range of 2 K–300 K with a linear part below 10 K, characteristic of conduction electrons of metallic materials. The electron density of states (DOS) calculations for Ti3C2OH-MXene reveal a significant DOS value at the Fermi level, with a large slope, confirming its metallic character, which is consistent with the experimental findings. The temperature dependence of electrical resistivity of the MXene samples was tested for a wide temperature range (3 K–350 K) and shows a decrease on lowering temperature with an upturn at low temperatures, where negative magnetoresistance is observed. The magnetoresistance versus field is approximately linear and increases its magnitude with decreasing temperature. The magnetization curves are straight lines with temperature-independent positive slopes, indicating Pauli paramagnetism due to conduction electrons.
A study of Ti3Al1−xSixC2 (x = 0 to x = 1) MAX-phase alloys is reported. The materials were obtained from mixtures of Ti3AlC2 and Ti3SiC2 powders with hot pressing sintering technique. They were characterised with X-ray diffraction, heat capacity, electrical resistivity, and magnetoresistance measurements. The results show a good quality crystal structure and metallic properties with high residual resistivity. The resistivity weakly varies with Si doping and shows a small, positive magnetoresistance effect. The magnetoresistance exhibits a quadratic dependence on the magnetic field, which indicates a dominant contribution from open electronic orbits. The Debye temperatures and Sommerfeld coefficient values derived from specific heat data show slight variations with Si content, with decreasing tendency for the former and an increase for the latter. Experimental results were supported by band structure calculations whose results are consistent with the experiment concerning specific heat, resistivity, and magnetoresistance measurements. In particular, they reveal that of the s-electrons at the Fermi level, those of Al and Si have prevailing density of states and, thus predominantly contribute to the metallic conductivity. This also shows that the high residual resistivity of the materials studied is an intrinsic effect, not due to defects of the crystal structure.
1 October 2019 in International Journal of Self-Propagating High-Temperature Synthesis
A large group of industrial and municipal waste are glassy in nature. One of the main directions of their use is thermal treatment, which aims to melt them (solid waste) or sinter (powdered waste). Fine grained glass cullet as well as silica fly ash was the subject of our research. During heating of glassy powders, high sintering dynamics is observed along with the accompanying glass devitrification process. Our objective in this research was to partially or entirely decouple the simultaneous occurrence of glass crystallization reaction and the sintering process during the heat treatment of glassy wastes. We divided an experiment onto two parts, first we compared the effects of thermal treatment on glass in the form of: pressed powder and a bulk glass. In the second experiment the influence of the powder sample density on the progress of glass crystallization was analysed. Results of our study indicate that physical sintering of glassy powders can lower the devitrification temperature of this material. However, physical sintering is accompanied by shrinkage, which when high density is achieved can limit the expansive growth process of grains formed during devitrification. Graphical abstract
Publikacja stanowi nowoczesny skrypt do zajęć laboratoryjnych z zakresu podstawowych właściwości materiałów inżynierskich, przeznaczony dla studentów kierunków technicznych. Opracowanie powstało na podstawie wieloletniego doświadczenia dydaktycznego oraz badawczego autorów, aktywnie działających w obszarze inżynierii materiałowej, i uwzględnia aktualny stan wiedzy oraz współczesne metody badań materiałowych. Książka została przygotowana w spójnej i przejrzystej formule dydaktycznej. Każdą część opracowano według jednolitego schematu obejmującego cel ćwiczenia, zagadnienia do samodzielnego przygotowania, część teoretyczną oraz szczegółowy opis części praktycznej wraz z zasadami opracowania wyników, a także przykładowe zagadnienia do dyskusji i kontrolne pytania. Każde ćwiczenie zakończone jest spisem literatury poszerzającej wiedzę w danym obszarze. Taki logiczny układ treści ułatwia studentom przygotowanie się do zajęć laboratoryjnych, sprzyja systematyzacji wiedzy oraz kształtuje w uczestnikach zajęć dobre nawyki eksperymentalne i umiejętność analizy wyników. Zakres tematyczny skryptu obejmuje m.in. pomiary podstawowych wielkości geometrycznych, ilościową analizę mikrostruktury materiałów, badanie gęstości i porowatości, zagadnienia związane z właściwościami sprężystymi, cieplnymi, wytrzymałościowymi, termomechanicznymi, a także właściwościami elektrycznymi i optycznymi materiałów. W realizacji ćwiczeń przewidziano wykorzystanie nowoczesnej aparatury badawczej oraz aktualnych modeli naukowych. Publikacja wyróżnia się klarownym, poprawnym językiem, unikającym żargonowych sformułowań charakterystycznych dla wielu technicznych publikacji, i przede wszystkim – wysokim poziomem merytorycznym. Skrypt adresowany jest do studentów studiów I, II i III stopnia kierunków technicznych, w szczególności inżynierii materiałowej, mechanicznej i elektrotechniki, i może stanowić wartościowe wsparcie w prowadzeniu zajęć laboratoryjnych oraz kształceniu praktycznych kompetencji inżynierskich.