Joao L. A. de Melo

Joao L. A. de Melo

Auto-generated profile, based on publicly available information

Joao L. A. de Melo

Department of Electrical and Computer Engineering, Faculty of Sciences and Technology, Universidade Nova de Lisboa, Caparica, Portugal

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 August 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
JMJoao L. A. de Melo
Joao L. A. de Melo
NPNuno Paulino
Nuno Paulino
João GoesJoão Goes
João Goes
Due to the emerging systems with constraints in terms of power and costs, such as smart sensor interfaces for the Internet-of-Things, the design of the ADCs becomes very challenging. In this paper, energy and area efficient techniques for continuous-time (CT) delta-sigma modulators (AΣMs) are discussed. These techniques are based on increasing the contribution of the 1-bit comparator to the loop gain by using passive RC integrators together with low gain amplifiers in the AΣM loop filter. A third-order CT AΣM is designed using these techniques to demonstrate their validity, and it achieves 27.5 fJ/conv.-step of energy efficiency. Due to the many design issues, such as the tradeoff between RC variations and loop stability, the design of this modulator has been optimized using a genetic algorithm. The 65-nm CMOS AΣM occupies only 0.013 mm2, dissipates 256 μW from a 0.7-V supply and it achieves a peak SNDR of 69.1 dB in a 2-MHz bandwidth. The dynamic range reaches 76.2 dB, which corresponds to a FoMSchreier of 175.1 dB.

1 May 2012
Verified
Conference Paper
Closed access
JMJ. L. A. de Melo
J. L. A. de Melo
BNB. Nowacki
B. Nowacki
NPN. Paulino
N. Paulino
João GoesJoão Goes
João Goes
The design of Sigma-Delta modulators (ΣΔMs) encompasses different variables that need to be optimized together in order to maximize the performance. The design task is even more complex due to the non-linear behavior of the quantizer. Typically, a linearized model of the quantizer is used to obtain linear equations that predict the performance of the modulator, which may cause significant discrepancies between the predicted and actual behavior of ΣΔMs. To better predict the behavior of a given design solution, we propose a design methodology for ΣΔMs based on a genetic algorithm (GA) that uses both linear equations and simulations: the design solution is evaluated using the equations and, if the performance is good enough, it will be evaluated trough simulation. This hybrid cost function allows to use a GA with a large population and, therefore, obtains the best possible design solution. The hybrid cost function takes thermal noise, quantization noise, voltage swing variations and stability of the modulator into account. Furthermore, it also selects the design solution that is the most insensitive to component variations. The design of a continuous-time (CT) and a discrete-time (DT) ΣΔM are given as proof-of-concept.

6 August 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
HSHugo Serra
Hugo Serra
IBIvan Bastos
Ivan Bastos
JMJoao L. A. de Melo
Joao L. A. de Melo
JPJoao Pedro
Joao Pedro
NPNuno Paulino
Nuno Paulino
TBTarik Bourouina
Tarik Bourouina
This paper presents an analog front-end (AFE) specially developed for a water conductivity measurement system for water network management applications. Water conductivity is one of the best ways to detect a problem with the water in the network. In order to trigger an alarm it is only required to detect a 10 % variation, which allows to simplify the system design. The proposed sensor uses four platinum micro-machined electrodes, where a 6 kHz signal is applied to the outer electrodes and a voltage signal is read in the inner ones. A programmable switched-capacitor (SC) bandpass filter is included in the analog-to-digital (A/D) channel to attenuate the interference from the 50 Hz power network, that shares the same environment with the water network, and to allow using a square wave signal to drive the sensor, thus simplifying the overall system. The resulting sine wave is digitized using a passive continuous-time (CT) 2nd order Σ modulator. The output bitstream is decimated, using a sinc filter, and the RMS value of the voltage is calculated. The A/D acquisition channel was implemented in a 130 nm CMOS technology, using a supply voltage of 0.9 V and a clock frequency of 1 MHz (SC amplifier and SC bandpass filter) and 4 MHz (Σ modulator). Measurement results show a SNDR of 44.4 dB for an input signal of 6 kHz and an amplitude of -41 dBV. The channel dissipates 386 μW and occupies an area of 0.27 mm.

12 July 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
JMJoao L. A. de Melo
Joao L. A. de Melo
NPNuno Pereira
Nuno Pereira
PLPedro V. Leitao
Pedro V. Leitao
NPNuno Paulino
Nuno Paulino
João GoesJoão Goes
João Goes
In the design of sigma-delta modulators ( $\Sigma \Delta $ Ms), different variables need to be optimized together in order to maximize the performance. This design task has the added difficulty of dealing with the non-linear behavior of the quantizer. Although a linearized model of the quantizer can be used, this may result in significant discrepancies between the predicted and actual behavior of the $\Sigma \Delta \text{M}$ . To better predict the behavior of a given design, we propose a design methodology for $\Sigma \Delta $ Ms based on a genetic algorithm (GA) that uses both linear equations and simulations. In order to reduce the computation time, the design solution is initially evaluated using equations and only if the performance is deemed good enough, it is subjected to a more refined simulation. This more precise simulation takes into account thermal noise, finite output swing, and gain (among other non-idealities) of the building blocks of the modulator. Moreover, Monte Carlo (MC) analyses are performed during the optimization in order to assess the sensitivity to component variations of the solutions. In order to demonstrate the validity and robustness of the proposed optimization methodology, several $\Sigma \Delta $ Ms designs are presented, together with the corresponding measured results.

1 December 2015 in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
Verified
Journal Article
Open access
PDF file
Pawel SniatalaPawel Sniatala
Pawel Sniatala
MNMariusz Naumowicz
Mariusz Naumowicz
AHA. Handkiewicz
A. Handkiewicz
Szymon SzczęsnySzymon Szczęsny
Szymon Szczęsny
JMJ.L.A. de Melo
J.L.A. de Melo
João GoesJoão Goes
João Goes
The paper presents a second order current mode sigma-delta modulator designed with the help of a new elaborated tool to optimize the transistor sizes. The circuit is composed of two continuous time loop filters, a current comparator and a one bit DAC with a current output. The resulting circuit, designed in a 65 nm 1.2 V CMOS technology, has a bandwidth of 2 MHz for a clock frequency of 250 MHz. The electrical simulation results show that it achieves a maximum signal-to-noise-plus-distortion ratio (SNDR) of 53.6 dB while dissipating 93 μW, which corresponds to an efficiency of 59.7 fJ/conv. The fully current mode structure makes the circuit suitable to be applied in a current mode signal processing like biosensors or image pixels arrays.

25 June 2025 in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
Verified
Journal Article
Open access
JSJ. Sonneveld
J. Sonneveld
RBR. Barthel
R. Barthel
SBS. Bugiel
S. Bugiel
LCL. Cecconi
L. Cecconi
JMJ. De Melo
J. De Melo
HWH. Wennlöf
H. Wennlöf