A means of enhancing electrical and thermal conductivities of carbon fibre reinforced polymer (CFRP) composites is investigated for the purpose of reducing damage when electric current and/or heat is introduced into a CFRP structure. The addition of commercially available graphene oxide (GO) nano-flakes dispersed into an epoxy resin is studied; quantities up to 6.3 vol% are used in a vacuum infusion process with carbon fibre fabric to form CFRP laminates. Measurements of the anisotropic electrical and thermal conductivity of the laminate were conducted on CFRP specimens with and without the GO nano-flakes. It is shown that the electrical conductivity in the through-thickness direction increased markedly, reaching values up to 0.18 S/cm, when 6.3 vol% of GO was added into the epoxy, showing a threefold increase compared to the neat CFRP. Similar improvement was also found in the thermal through-thickness conductivity for the same filler content, where the laminate exhibited identical values in both transverse and through-thickness directions. However, the properties transverse to the fibres were not greatly affected by the GO addition. To assess the effect of the GO on the mechanical properties, interlaminar shear strength tests were conducted that showed that the addition of the GO significantly enhanced the through-thickness shear strength.
28 February 2018 in Journal of Physics D: Applied Physics
In this paper partial discharge (PD) is investigated inside a spherical air filled void at atmospheric pressure using a drift diffusion model. Discharge dynamics consisted of an electron avalanche transitioning into positive streamer, in agreement with earlier work on dielectric barrier discharges. Different model configurations were utilised to test many of the concepts employed in semi-analytical PD activity models, which use simplistic descriptions of the discharge dynamics. The results showed that many of these concepts may be erroneous, with significant discrepancies between the canonical reasoning and the simulation results. For example, the residual electric field, the electric field after a discharge, is significantly lower than the estimates used by classical PD activity models in the literature.
1 November 2020 in Plasma Sources Science and Technology
A thermionic plasma source apparatus has been developed and characterised for high-density gaseous plasma antenna (GPA) applications. The system produces a cylindrical plasma column which is 100 mm long with a diameter of 8 mm and operates with a total plasma power consumption of 70 to 200 W, depending mainly on the DC discharge current. The plasma column electron density and temperature is measured via microwave interferometry and optical emission spectroscopy. The plasma properties are investigated for Ar, Kr and Xe at pressures from 1 to 4 mbar. The system has demonstrated higher electron densities (>1019 m−3) at low pressures (<2 mbar) than has been experimentally achieved before for GPA applications. This could allow for high gain GPA operation comparable to that of conventional metallic antennas. Additionally, the source has demonstrated operation over a wide range of electron densities, from 2 × 1018 to 1 × 1019 m−3, which can allow for frequency hopping. The plasma columns electron temperature remains around 1.5 eV for argon, largely uninfluenced by the pressure or discharge current. These plasma column measurements obtained are used to analyse the plasma properties influence on GPA performance. This analysis indicates that at high density operation, a gain is achieved which is only 22% lower than that of the conventional metallic antenna. Furthermore, the density ranges demonstrated could enable wide-range frequency hopping of over 100 MHz, with a gain greater than 1.3 dBi.
7 November 2007 in Journal of Thermal Spray Technology
The sintering of free-standing plasma sprayed TBCs has been modeled, based on variational principles of free energy minimization and comparisons are made with experimental results. Predictions of through-thickness shrinkage and changing pore surface area are compared with the experimental data obtained by dilatometry and BET analysis, respectively. The sensitivity of the predictions to initial pore architecture and material properties is assessed. The model can be used to predict the evolution of the contact area between overlying splats. This is in turn related to the through-thickness thermal conductivity, using a previously developed analytical model (I.O. Golosnoy, et al. J. Therm. Spray Technol., 2005, 14(2), p 205-214).
Cellulose particle accumulation under AC, DC and DC biased AC electric field in transformer oil has been investigated in this paper. Different levels of particle concentrations tested with spherical electrode system. Optical microscopic images and conduction current of the particle accumulation process have been recorded during the experiments. A complete bridge of cellulose particles only observed under DC and DC biased AC electric field.