The 2D insulating material hexagonal boron nitride (h‐BN) has attracted much attention as the active medium in memristive devices due to its favorable physical properties, among others, a wide bandgap that enables a large switching window. Metal filament formation is frequently suggested for h‐BN devices as the resistive switching (RS) mechanism, usually supported by highly specialized methods like conductive atomic force microscopy (C‐AFM) or transmission electron microscopy (TEM). Here, the switching of multilayer hexagonal boron nitride (h‐BN) threshold memristors with two nickel (Ni) electrodes is investigated through their current conduction mechanisms. Both the high and the low resistance states are analyzed through temperature‐dependent current–voltage measurements. The formation and retraction of nickel filaments along boron defects in the h‐BN film as the resistive switching mechanism is proposed. The electrical data are corroborated with TEM analyses to establish temperature‐dependent current–voltage measurements as a valuable tool for the analysis of resistive switching phenomena in memristors made of 2D materials. The memristors exhibit a wide and tunable current operation range and low stand‐by currents, in line with the state of the art in h‐BN‐based threshold switches, a low cycle‐to‐cycle variability of 5%, and a large On/Off ratio of 107.
We present the development of application-specific silicon-on-insulator SOI nanowire ring and racetrack resonators designed to assist semiconductor optical amplifier (SOA)-based all-optical wavelength conversion. We demonstrate the fabrication of fix resonance racetrack resonators exhibiting coupling gaps as low as 160 nm and tunable ring resonators with coupling gaps <; 90 nm. The resonators are cascaded after commercial 40 Gb/s SOAs to realize chirp filtering of the optical data signals through high-resolution spectral sampling. We experimentally demonstrate inverted and non-inverted SOI resonator-assisted all-optical wavelength conversion at 40 Gb/s and 160 Gb/s with power penalties <; 3 dB.
Memristors based on 2D materials have garnered significant attention. Their fast resistive switching (RS) behavior and atomic‐level thickness enable low power consumption, making them promising candidates for neuromorphic computing. Among these, memristors based on molybdenum disulfide (MoS 2 ) have been extensively studied. Their RS has been attributed to the formation and rupture of conductive filaments (CFs). However, the underlying mechanism of filament formation remains underexplored, and the inherently stochastic nature of RS leads to high variability and limited reproducibility. In this study, we demonstrate wafer‐scale memristors based on metal–organic chemical vapor‐deposited MoS 2 . Our devices exhibit both volatile and nonvolatile RS behaviors, tunable by modulating the current compliance. Notably, we observe stable RS characteristics in an intermediate resistive state (IRS), set and reset voltages within ±1 V, endurance of over 2500 cycles, and state retention over 10 6 s. Among 100 tested devices, 98 exhibited IRS behavior, confirming a high yield (98%) and demonstrating its robust and reproducible RS nature. Combined experimental and simulation results further indicate that the IRS arises from the lateral growth of CFs in the van der Waals gaps. Furthermore, the devices successfully emulate synaptic plasticity with current responses on a microsecond timescale, highlighting their potential for large‐scale integration in neuromorphic computing architectures.
Two‐dimensional (2D) materials such as molybdenum disulfide (MoS 2 ) show promise for memristor applications. Most MoS 2 memristors use vertical metal/MoS 2 /metal stacks with gold or silver active electrodes and rely on electron‐beam evaporation; sputtering is seldom used. This study investigates palladium (Pd), nickel (Ni), and aluminum (Al) as electrodes and compares resistive switching (RS) performance for sputtered versus evaporated top electrodes. Pd acts as a passive electrode with minimal contribution to RS. Devices with Ni active electrodes exhibit very low initial resistance and a small RS window, consistent with deposition‐induced damage to MoS 2 . Sputtered Al yields highly reproducible RS in Pd/MoS 2 /Al memristors, achieving 95% yield across 64 devices. In contrast, evaporated Al forms a parasitic oxide at the Al/MoS 2 interface that inhibits RS, even when deposited at a base pressure comparable to that of sputtered Al. Area scaling and temperature‐dependent measurements indicate Al filament formation and dissolution via electrochemical metallization as the RS mechanism. Metal‐specific energy barriers for filament formation explain the superior performance of sputtered Al. Overall, the results identify Al as an effective active electrode within the investigated device architecture and show that sputtering is a viable alternative for top‐electrode deposition because it suppresses interfacial oxide formation.