1 April 2017 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
With technology down scaling, static power has become one of the biggest challenges in a system on chip. Normally off computing using nonvolatile (NV) sequential elements is a promising solution to address this challenge. Recently, many NV shadow flip-flop architectures have been introduced in which magnetic tunnel junction (MTJ) cells are employed as backup storing elements. Due to the emerging fabrication processes of magnetic layers, MTJs are more susceptible to manufacturing defects than their CMOS counterparts. Moreover, unlike memory arrays that can effectively be repaired with well-established memory repair and coding schemes, flip-flops scattered in the layout are more difficult to repair. Therefore, without effective defect and fault tolerance for NV flip-flops, the manufacturing yield will be affected severely. In this paper, we propose a fault-tolerant NV latch (FTNV-L) design, in which several MTJ cells are arranged in such a way that it is resilient to various MTJ faults. The simulation results show that our proposed FTNV-L can effectively tolerate all single MTJ faults with a considerably lower overhead than traditional approaches.
25 October 2022 in ACM Journal on Emerging Technologies in Computing Systems
Faster and cheaper computers have been constantly demanding technological and architectural improvements. However, current technology is suffering from three technology walls: leakage wall, reliability wall, and cost wall. Meanwhile, existing architecture performance is also saturating due to three well-known architecture walls: memory wall, power wall, and instruction-level parallelism (ILP) wall. Hence, a lot of novel technologies and architectures have been introduced and developed intensively. Our previous work has presented a comprehensive classification and broad overview of memory-centric computer architectures. In this article, we aim to discuss the most important classes of memory-centric architectures thoroughly and evaluate their advantages and disadvantages. Moreover, for each class, the article provides a comprehensive survey on memory-centric architectures available in the literature.
26 July 2022 in IEEE Transactions on Emerging Topics in Computational Intelligence
Computation-in-memory (CIM) paradigm leverages emerging memory technologies such as resistive random access memories (RRAMs) to process the data within the memory itself. This alleviates the memory-processor bottleneck resulting in much higher hardware efficiency compared to von-Neumann architecture-based conventional hardware. Hence, CIM becomes an attractive alternative for applications like neural networks which require a huge number of data transfer operations in conventional hardware. CIM-based neural networks typically employ bit-slicing scheme which represents a single neural weight using multiple RRAM devices (called slices) to meet the high bit-precision demand. However, such neural networks suffer from significant accuracy degradation due to non-zero G$_{\min }$ error where a zero weight in the neural network is represented by an RRAM device with a non-zero conductance. This paper proposes an unbalanced bit-slicing scheme to mitigate the impact of non-zero G$_{\min }$ error. It achieves this by allocating appropriate sensing margins for different slices based on their binary positions. It also tunes the sensing margins to meet the demands of either high accuracy or energy-efficiency. The sensing margin allocation is supported by 2’s complement arithmetic which further reduces the influence of non-zero G$_{\min }$ error. Simulation results show that our proposed scheme achieves up to 7.3× accuracy and up to 7.8× correct operations per unit energy consumption compared to state-of-the-art.
22 June 2022 in Neuromorphic Computing and Engineering
Computation-in-memory using memristive devices is a promising approach to overcome the performance limitations of conventional computing architectures introduced by the von Neumann bottleneck which are also known as memory wall and power wall. It has been shown that accelerators based on memristive devices can deliver higher energy efficiencies and data throughputs when compared with conventional architectures. In the vast multitude of memristive devices, bipolar resistive switches based on the valence change mechanism (VCM) are particularly interesting due to their low power operation, non-volatility, high integration density and their CMOS compatibility. While a wide range of possible applications is considered, many of them such as artificial neural networks heavily rely on vector-matrix-multiplications (VMMs) as a mathematical operation. These VMMs are made up of large numbers of multiplication and accumulation (MAC) operations. The MAC operation can be realised using memristive devices in an analog fashion using Ohm’s law and Kirchhoff’s law. However, VCM devices exhibit a range of non-idealities, affecting the VMM performance, which in turn impacts the overall accuracy of the application. Those non-idealities can be classified into time-independent (programming variability) and time-dependent (read disturb and read noise). Additionally, peripheral circuits such as analog to digital converters can introduce errors during the digitalization. In this work, we experimentally and theoretically investigate the impact of device- and circuit-level effects on the VMM in a VCM crossbars. Our analysis shows that the variability of the low resistive state plays a key role and that reading in the RESET direction should be favored to reading in the SET direction.
12 August 2019 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
With the widespread use of electronic devices in embedding or processing sensitive information, new hardware security primitives have emerged to improve the shortcomings of traditional secure data storage. One of these solutions, the physically unclonable function (PUF), which is widely used for authentication and cryptography applications, extracts the unique and unclonable value from the circuit physical properties. However, a cloning attack on memory-based PUF has been demonstrated from the circuit back-side tampering, questioning its unclonable property and opening counterfeiting vulnerability in an untrusted supply chain. Spin transfer torque-magnetic random-access memory (STT-MRAM) is a promising technology due to its nonvolatility, scalability, and CMOS compatibility, therefore envisioned to be used in many embedded secure devices. In this paper, we reveal the vulnerability of existing STT-MRAM PUF solutions to back-side attacks by modeling different levels of tampering and their impact at electrical and logical levels. We propose a tamper resilient methodology for the STT-MRAM PUF design based on its switching properties. The resilience of the proposed solution to different levels of tampering and a 100% detection are confirmed with simulation results.
3 March 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
Emerging computation-in-memory (CIM) paradigm offers processing and storage of data at the same physical location, thus alleviating critical memory-processor communication bottlenecks suffered by conventional von-Neumann architecture. Storage of data in a CIM architecture is analog in nature and therefore computation is performed in analog domain i.e. inputs and outputs are analog values. Since the outside computing environment is digital, analog-to-digital converters (ADC) are utilized to perform the output data conversion. However, ADC designs are bulky, power-hungry circuits that are prone to design variations and therefore, play an important role in determining the computing efficiency of CIM architectures. In this paper, we present a scalable and reliable integrate and fire circuit ADC (SRIF-ADC) design for CIM architectures, suitable for stringent power and area constraints. We devise a technique to stabilize the node receiving analog inputs that allows more rows to be activated at the same time, thereby increasing the operand size of input vectors. This allows better scalability in terms of higher parallelism of operations. We employ a self-timed variation-aware design approach and design measures to drastically reduce read disturb of memristor devices that address reliability issues related to the ADC design. In addition, we present a compact, built-in sample-and-hold circuit to replace the large-sized capacitance and built-in weighting technique to alleviate the need for post-processing. For multiply-and-accumulate (MAC) operation, our simulation results show that we can improve the computational parallelism by 3X as well as ADC conversion speed and energy efficiency are improved by 2X and 11.6X, respectively, compared to the state-of-the-art design.