This letter proposes an ultralow power single-inductor multiple-output converter for an implantable stimulation system. This converter minimizes the number of switches turning on and off to deliver power to outputs of 0.8, 1.8, and 20 V, and it uses a soft-switching technique for all switching nodes. It also operates with a self-oscillating controller only when outputs require power. As a result, it has a peak efficiency of 92.3% when the converter generates the outputs of 0.8 and 1.8 V, of which load currents are 2 and 0.5 mA, respectively, from a battery voltage of 3 V. The converter consumes a quiescent power of less than 3.0 μ W.
17 March 2022 in IEEE Transactions on Power Electronics
This paper proposes an input-independent loop type-III buck converter (ILT3C) enhancing the security of edge devices. Compared to a conventional type-III buck converter (CT3C), the ILT3C maximally improves PSRR as much as 34.1 dB to be robust against power injection attack (PIA). It also reduces the peak of EMI as much as 35.8 dBV to enhance security from power side-channel attack (PSCA). Furthermore, the external components such as an inductor and a capacitor of the converter should be integrated into a package to minimize its exposure to unknown hacking risks. Thus, the proposed converter operates with a high switching frequency (fsw) of 20 MHz and it can reduce the size of the external components enough to be placed in the package. The prototype converter was implemented in a 0.18-m CMOS process. This ILT3C achieves the maximum efficiency of 90.7% and occupies an active area of 0.195 mm2.
In portable mobile devices, the capacitor-less low-dropout regulator (LDO) is in great demand as a power management unit to achieve complete on-chip design [1] –[6]. In the capacitor-less LDO, it is important to achieve two things: good load/line regulations and a fast transient response.
25 September 2023 in IEEE Journal of Solid-State Circuits
This article presents a single-inductor bipolar-output (SIBO) converter for active-matrix organic light-emitting diode (AMOLED) displays to reduce output ripples and enhance power conversion efficiency (PCE). We propose the simultaneous energy transferring SIBO (SETSIBO) converter, which generates bipolar outputs with only a two-phase operation and does not require additional switching. The hybrid power stage with a flying capacitor and two-phase operation reduces the dc value of the inductor current, which mitigates conduction losses and output ripples; moreover, the hybrid power stage allows the high-voltage switches in the conventional converters to be replaced by low-voltage switches. The inductor current reduction and the low-voltage power switch use improve the PCE. This article analyzes the proposed converter’s output ripple reduction and the PCE improvements; furthermore, the load imbalance is effectively compensated with the proposed SETSIBO converter. The prototype of the proposed SETSIBO is fabricated in a 0.5- $\mu \text{m}$ CMOS process. The measured ripples at positive and negative outputs are 24.5 and 28 mV, respectively, with a 300 mA load current $I_{\mathrm {o}}$ . The measured peak PCE is 94.1%, and the active area is 1.46 mm2.
Application of an intense, high quality, well-collimated probe beam is effective in improving the performance of the measurement. Such probe beam is produced by stabilization of the high frequency gyrotron output and its conversion into a Gaussian beam.
19 May 2025 in IEEE Transactions on Power Electronics
This article proposes an extended voltage-conversion-ratio (VCR) buck converter with a VCR of up to 0.67. Unlike previous hybrid converters with a VCR limit of under 0.5, the proposed converter reliably supplies power to power rails lower than 1.8 V over the entire operating range of a Li-ion battery without requiring additional external components. In addition, it minimizes every power loss from the dc resistance of an inductor, the equivalent series resistance of the flying capacitor, and on-resistance of power switches. As a result, it achieves higher efficiency while supplying a stable 1.8 V output voltage for mobile applications. In addition, because the proposed converter simply operates in two-phase mode in entire VCR range, it is simpler than previous works in which the controller changes their operation mode between two-phase mode and three-phase mode depending on the VCR. The chip was fabricated in a 250-nm complementary metal-oxide-semiconductor (CMOS) process and obtained a peak efficiency of 97.93% at VIN = 3.3 V, VO = 1.8 V, and IO = 0.3 A.