This work presents analytical expressions for the dc inductance of 3-D air-core inductors with circular cross-sectional pillars (CCSPs) and rectangular cross-sectional pillars (RCSPs). We consider the following four types of inductor structures: 1) a toroid with CCSP; 2) a toroid with RCSP; 3) a solenoid with RCSP; and 4) a solenoid with CCSP. For each type, a unique analytical model is developed for obtaining dc inductance. High-frequency (1–100 MHz) effects on inductance are also discussed. The inductance values predicted by the proposed analytical models of the first three types of inductor structures are in an acceptable agreement with numerical finite-element analysis (FEA) solutions, where the maximum difference is 7.3%. Also, our analytical model for the fourth-type inductor reduces the error, when correlated with FEA inductance value, up to $6\times $ compared with previously published models. A comparison of results using the proposed analytical expressions with published measured values as well as our measurement data demonstrates the error ranging from 0.5% to 16.2%, while conventional formulas show errors of up to 143%. The results of the proposed models could serve as a good initial estimate for power supply-on-chip (PwrSoC) and power supply in package (PSiP) applications.
23 March 2022 in Power Electronic Devices and Components
A solution architecture for monolithic system-on-chip (SoC) power conversion is in high demand to enable modern electronics with a reduced footprint and increased functionality. A promising solution is to reduce the microinductor size by using novel magnetically-enhanced 3-D design topologies. This work presents the design, modeling, and analysis of a 3-D spiral inductor with magnetic thin-films for power supply applications in the frequency range of 3–30 MHz. A closed-form analytical expression is derived for the inductance, including both the air- and magnetic-core contributions. To validate the air-core inductance model, we implement a 3-D spiral inductor on PCB. The theoretical calculation of air-core inductance is in good agreement with experimental data. To validate the inductance model of the magnetic-core, a 3-D spiral inductor is modeled with Ansys Maxwell electromagnetic field simulation software. A winding AC resistance model is additionally presented. We perform a design space exploration (DSE) to investigate the significance of the 3-D spiral inductor structure. Two important performance parameters are discussed: dc quality factor $(Q_{dc})$ and ac quality factor $(Q_{ac})$ . Also, a 3-D spiral inductor structure with magnetic thin-films is characterized in Ansys Maxwell to estimate its potential, and a novel fabrication method is proposed to implement this inductor. The measured relative permeability ( $\mu _{r}$ ) and the magnetic loss tangent ( $tan~\delta $ ) of Co-Zr-Ta-B magnetic thin-films, developed in-house, are used to simulate the proposed structure. The promising results of the DSE can be easily extended to improve the performance of other 3-D inductor topologies, such as the solenoid and the toroid. The numerical simulations reveal that the 3-D spiral inductor with magnetic thin-films has the potential to demonstrate a figure-of-merit (FOM) that is significantly higher than traditional inductors.
16 July 2025 in IEEE Journal of Emerging and Selected Topics in Power Electronics
One of the primary limiting factors presently inhibiting device miniaturisation is the current roadblock posed by the large size of inductors employed in power processing units. The miniaturisation and integration of the inductor is a challenge requiring innovations in novel inductor topologies. This paper reports the design, modeling, and analysis of a novel vertical magnetic-core inductor structure: coaxial cross-section of copper conductor and a magnetic core surrounding it. To evaluate the performance of the proposed inductor structure, we considered a range of performance parameters: inductance, saturation current, DC ratio of inductance to resistance (Qdc), AC quality factor (Qac), etc., which are essential figures-of-merit (FOM) of micro-inductors that are employed for energy storage in PwrSiP/PwrSoC applications. A novel two-dimensional graphical approach that correlates AC performance and DC performance is introduced.We derived an inductance model for the proposed structure. The measured relative permeability (μr) and the magnetic loss tangent (tan δ) of Co-Zr-Ta-B magnetic thin-films, developed in-house, are used to estimate the AC quality factor. Finally, the primitive structure of the proposed inductor is fabricated, and experimental results are presented to demonstrate that it is possible to realize the proposed structure in practice.