4 June 2021 in Journal of Electrical Engineering & Technology
31 October 2018 in IEEE Transactions on Power Electronics
22 August 2024 in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
Double-clamp zero-voltage-switching (DCZVS) fullbridge flyback converter is one of the most attractive solutions for high power density applications with wide input range, because of its features of primary side regulation (PSR) and excellent softswitching. By analyzing the ZVS process and the maximum output power at maximum flux, this paper reveals that the dead-time is one of the key parameters to restrict the output power of the DCZVS converter at high switching frequency. Then, the multicell transformer-coupled input-series-output-parallel (ISOP) structure is proposed in this paper to shorten the dead-time so as to improve the output power of the DCZVS converter, which does not increase the size of the transformer. In the multi-cell converters, the number of cells and the transformer design are also discussed. Finally, A DCZVS prototype with two transformercoupled ISOP cells is built up to validate the design, which achieves a wide input range of 160V-420V and realizes a 28V/20A output with a power density of 1203 W/inch3 and a peak efficiency of 93.69%. Compared with the original DCZVS converter, the proposed two-cell DCZVS converter achieves a 15% increase in power density with the same transformer size and maximum flux.
9 August 2017 in IET Power Electronics
A new buck inverter without shoot‐through problem is presented and analysed in this study. The traditional dual‐buck inverter has been proposed to solve the shoot‐through problem of bridge‐type inverters, eliminate the dead‐time effect and improve the reliability along with the conversion efficiency. However, the existing dual‐buck inverter is prone to result in the problem of circulation and low utilisation rate of input voltage in half‐bridge‐type inverters. Besides, two or even four inductors are needed in the traditional dual‐buck inverter configuration, which leads to a larger volume and weight. In this study, single inductor and single power are used in the proposed buck inverter topology. The operating circuit is equivalent to a buck circuit during each mode, and only one switch works in high‐frequency condition at any time. A 1‐kW prototype is established and tested in this study. The results of simulation and experiments verify the validity of the theoretical analysis, along with the good performance in situations where small size, high conversion efficiency and high stability are required.
3 July 2018 in IET Power Electronics
A 1500 V three‐level forward converter with phase‐shifted control is proposed to meet therequirements on medium‐ and high‐voltage DC bus of photovoltaic grid‐connectedsystem. The architecture of 1500 V DC bus is established by filtering thephase‐shifted outputs in series centrally, in which the internal filters of eachDC/DC converter are removed. The three‐level voltage is superimposed byphase‐shifting the rectified output voltages in series, which is beneficial todecrease the inductor current pulsation, diminish the ripple of output voltageand improve the system efficiency. The centralised filter contributes todownsizing the filter and reducing the system cost. With the introduction ofparallel‐series structure, the characteristics of low‐voltage stress areretained and the power transmission is improved. Meanwhile, the minimum value oftotal harmonic distortion (THD) with phase‐shifted control is obtained throughthe Fourier decomposition of three‐level voltage waveform. By analysing thevariation rule of THD with the change of conduction angle, the optimalsteady‐state operating point of the converter is achieved. The operatingprinciple of the proposed system is presented minutely in this study and aprototype has been established. The experimental results verify the validity ofthe proposed converter.
6 November 2023 in IEEE Transactions on Power Electronics
The contactless rotary transformer based on wireless power transmission technology can solve the problems of excessive friction loss and low system stability, which caused by the rotation of traditional conductive slip rings in the operation time. In this paper, an external embedded multi-U-shaped rotary transformer(EEMUCRT) based on discrete spliced core is proposed. This structure embeds the outer core into the inner core. Compared with the structures mentioned earlier in the article, the coupling coefficient of the system is higher on the premise of smaller volume and weight. Based on the analysis of the magnetic core arrangement and the magnetic circuit model, the optimal structural parameters and arrangement of the primary and secondary magnetic cores are obtained by theoretical calculation and simulation. In order to verify the rotational stability and offset tolerance of the structure, an experimental prototype was built, and the results showed that the EEMUCRT can transmit energy efficiently and has good stabilit