9 June 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Active clamp flyback (ACF) converter has been demonstrated that which is better than traditional flyback in high-frequency power-adaptor applications. According to the circuit structure, ACF has two modes, primary resonant ACF (PR-ACF) and secondary resonant ACF (SR-ACF). In order to improve the power density, a high-precision primary side regulation (PSR) constant voltage control method for ACF converter is proposed in this paper. The proposed method not only can be effectively adopted in PR-ACF but SR-ACF converter. The high-precision output voltage is predicted by highly accurate sampling points on primary auxiliary voltage. The applied micro controller environment improves the practicability and increases the power density of the ACF system. To verify the proposed PSR method, a prototype which can be changed to PR-ACF and SR-ACF is designed. The output voltage offset, operation efficiency and dynamic performance are analyzed. The tested results show highprecision output is obtained in ACF converter by using the proposed method, the maximum output voltage deviation which are 4% and 3.5% in PR-ACF and SR-ACF converter, respectively. Moreover, SR-ACF has a higher efficiency compared to PR-ACF converter, and a smaller voltage shoot during dynamic process, but which need a larger regulation time since the additional output inductor.
22 January 2025 in IEEE Transactions on Power Electronics
The quadrilateral control method for four-switch Buck–Boost converter can enable all of the power switches to achieve zero-voltage-switching (ZVS), thereby achieving high power density. However, the inductor current requires to be sensed and regulated to ensure the realization of ZVS, which will introduce the additional losses and degrade the efficiency. In this article, a high-efficiency control strategy based on lossless current sampling is proposed, which can achieve the minimum height of the inductor current over the whole working conditions. Moreover, to ensure the smooth switching between different modes, a transition mode is inserted when the input voltage is close to the output voltage. Finally, a prototype with input voltage of 40–60V and output parameters of 48V/6A is built to verify the effectiveness of the proposed sampling circuit and control strategy. The peak efficiency is 98.88%, while the full-load efficiency at the nominal input voltage is 98.14%. Meanwhile, a video material is provided to demonstrate the extremely low root mean square (RMS) value of the inductor current and the smooth switching process under different input voltage and load conditions.
23 July 2024 in IEEE Transactions on Circuits and Systems I: Regular Papers
There are two drawbacks in the previous tri-mode variable-frequency peak current mode (VFPCM) control for primary side regulation (PSR) double-clamp zero voltage switching (DCZVS) flyback converter: firstly, the current-sense resistor leads to non-negligible loss at high power and instability at high frequency; secondly, the previous tri-mode control suffers from poor dynamic performance and lacks accurate small-signal model in various control modes. In this paper, a novel sensorless current quad-mode control is proposed, which eliminates the current-sense resistor by input voltage feed-forward and improve the dynamic performance by introducing hybrid mode (HYM) and seamless mode-switch. In addition, a unified small-signal model of the four control modes is derived in the paper, which explains the high dynamic performance of the introduced HYM. The proposed sensorless current quad-mode control and the unified small-signal model are validated on a 16-50V input and 28V/320W output experimental prototype. Compared with the traditional tri-mode peak current mode control, the undershoot recovery time and overshoot recovery time of the proposed control scheme are reduced from 12ms to 2.0ms and 12ms to 1.6ms, respectively.
22 August 2024 in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
Double-clamp zero-voltage-switching (DCZVS) fullbridge flyback converter is one of the most attractive solutions for high power density applications with wide input range, because of its features of primary side regulation (PSR) and excellent softswitching. By analyzing the ZVS process and the maximum output power at maximum flux, this paper reveals that the dead-time is one of the key parameters to restrict the output power of the DCZVS converter at high switching frequency. Then, the multicell transformer-coupled input-series-output-parallel (ISOP) structure is proposed in this paper to shorten the dead-time so as to improve the output power of the DCZVS converter, which does not increase the size of the transformer. In the multi-cell converters, the number of cells and the transformer design are also discussed. Finally, A DCZVS prototype with two transformercoupled ISOP cells is built up to validate the design, which achieves a wide input range of 160V-420V and realizes a 28V/20A output with a power density of 1203 W/inch3 and a peak efficiency of 93.69%. Compared with the original DCZVS converter, the proposed two-cell DCZVS converter achieves a 15% increase in power density with the same transformer size and maximum flux.
5 September 2023 in IEEE Transactions on Power Electronics
V DS (drain-source voltage) based synchronous rectifiers (SRs) are widely used due to their simplicity and low cost. However, there are still three obvious issues. (1) The premature turn-off caused by parasitic inductance under high frequency. (2) The turn-on propagation delay is typically tens of nanoseconds. (3) Commercial SRs usually have a limited V DS rating of about 200V. To solve the above problems, a high-speed SR (including a customized SR IC and a peripheral circuit) is proposed. A high-speed comparator together with a slope detection circuit is proposed to reduce the turn-on delay, and the proposed fully integrated synchronous rectifier IC is implemented in a 1-μm Bipolar process with a die area of 1.47*1.98mm 2 . The peripheral circuit contains the improved dead time compensation circuit, the self-driven high-voltage isolation circuit, and the power supply circuit for SR IC, and the component count is reduced by device reuse. In a 200W DCZVS buck-boost converter prototype, the proposed SR can achieve a switching frequency of more than 700 kHz with minimal dead time, the turn-on propagation delay including peripheral circuits and SR IC is reduced to 8.1 ns, the isolated drain-source voltage is limited to within 10V, and the peak efficiency is 93.6%.