In order to improve energy efficiency by increasing heat dissipation performance of bus-bar which distributes the current in high-power switchboard, the heat dissipation effects of the shape modification and surface treatment of Cu bus-bar were studied. The surface temperatures of the conventional plate-type bus-bar, and the improved tunnel-type bus-bar were compared by using electromagnetic and thermal analyses. The optimum thickness of tunnel-type bus-bar and the spacing and array among three bus-bars were calculated; and the surface temperature of tunnel-type bus-bar showed 7.9 °C lower than that of plate-type bus-bar in a 3-phase array condition. In addition, the surface and internal temperatures of the uncoated, CNT (Carbon nanotube)-coated, and BN (Boron nitride)-coated Cu bus-bars were measured with thermal imaging camera and the experiment using a hot plate. It was confirmed that the difference in the internal temperature between uncoated and BN-coated Cu was 19.4 °C. The application of the bus-bar improved from this study might contribute to the increase in power energy efficiency.
1 March 2023 in Transaction of the Korean Society of Automotive Engineers
When collecting dust samples from coal-fired power plant chimneys, a nozzle specially designed with an inlet shape of circle type is used for constant velocity suction. However, it is cumbersome to use nozzles with different areas depending on the flow rate. In this study, the effect of the nozzle inlet shape of the isokinetic sampler on the performance of constant velocity suction was evaluated through simulation. The simulations were conducted using the realizable k−ε model, which is known to be suitable for separation flow analysis for particles of 1–50 μm. The turbulent flow fully developed before reaching the inlet of the sampling probe, and the flow rate was set under the condition that the uniformity was secured at approximately 92% at least. The aspiration ratio was employed for evaluating the degree of constant velocity aspiration of the isokinetic sampling probe. It was found that the larger the particle diameter and the faster the flow rate, the larger the aspiration ratio for both the circular and ellipsoidal inlets. In particular, compared with the circular inlet, the aspiration ratio of the sampler with ellipsoidal inlet was closer to 1 in the free-flow velocity range, from 5 to 15 m/s. For this reason, if the ellipsoidal inlet nozzle is used by adjusting only the length parallel to the major axis, the maintenance cost is expected to be reduced compared to the circle-type nozzle.
In this paper, an optimal design model was developed to reduce noise and secure the torque performance of a brushless direct-current motor used in the seat of an autonomous vehicle. An acoustic model using finite elements was developed and verified through the noise test of the brushless direct-current motor. In order to reduce noise in the brushless direct-current motor and obtain a reliable optimization geometry of noiseless seat motion, parametric analysis was performed through the design of experiments and Monte Carlo statistical analysis. The slot depth, stator tooth width, slot opening, radial depth, and undercut angle of the brushless direct-current motor were selected as design parameters for design parameter analysis. Then, a non-linear prediction model was used to determine the optimal slot depth and stator tooth width to maintain the drive torque and minimize the sound pressure level at 23.26 dB or lower. The Monte Carlo statistical method was used to minimize the deviation of the sound pressure level caused by the production deviation of the design parameters. The result is that the SPL was 23.00–23.50 dB with a confidence level of approximately 99.76% when the level of production quality control was set at 3σ.
This study investigated the squeal mechanism induced by friction in a lead screw system. The dynamic instability in the friction noise model of the lead screw was derived through a complex eigenvalue analysis via a finite element model. A two degree of freedom model was described to analyze the closed solutions generated in the lead screw, and the friction noise sensitivity was examined. The analysis showed that the main source of friction noise in the lead screw was the bending mode pair, and friction-induced instability occurred when the ratio of the stiffness of the bending pair modes was 0.9–1. We also built an architecture to predict multiple outputs from a single model using deep neural networks and demonstrated that friction-induced instability can be predicted by deep neural networks. In particular, instability with nonlinearity was predicted very accurately by deep neural networks with a maximum absolute difference of about 0.035.
1 December 2023 in Transaction of the Korean Society of Automotive Engineers