Yudi Xiao

Yudi Xiao

Auto-generated profile, based on publicly available information

Yudi Xiao

Department of Electronic and Electrical Engineering, University of Strathclyde, Glasgow, U.K.

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 July 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
ZZZhe Zhang
Zhe Zhang
JHJiasheng Huang
Jiasheng Huang
YXYudi Xiao
Yudi Xiao
In this paper, a partial parallel dual active bridge (PPDAB) converter is proposed to lower the current stress over the switching devices on the low-voltage (LV) side. Gallium Nitride (GaN) transistors are used to improve efficiency and power density at 1 MHz switching frequency. Moreover, in order to reduce the number of magnetic components and achieve more compact design, with a unique three-leg core geometry, a new method of integrating three transformers and their associated interfacing inductors is proposed. The integration is able to shorten winding length and therefore reduces winding dc resistance. Moreover, wounding the secondary windings on each outer leg in the core enlarges leakage inductance, which can serve as the interfacing inductor Lac in the PPDAB converter. Given that, a reluctance model to analyze coupling effect of the secondary windings as well as their current balance is derived and validated by finite element simulations. Based on both calculations and simulations, the proposed integrated transformer is found to be functionally equivalent to three discrete transformers, in which their primary windings are connected in series, and the additional Lac inductor. Given the same number of the turns of the windings in each parallel module, the ac currents in these three secondary windings can inherently balance.

22 April 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
YXYudi Xiao
Yudi Xiao
ZZZhe Zhang
Zhe Zhang
Michael A.E. AndersenMichael A.E. Andersen
Michael A.E. Andersen
KSKai Sun
Kai Sun
Dual active bridge (DAB) converter's zero-voltage-switching (ZVS) and its range extension have been studied intensively. However, this paper proves that the external inductance location, i.e. placing on which side of the transformer, does affect the ZVS operation due to transformers' parasitic capacitances, in particular at a high switching frequency of higher than 1 MHz. Thus, this paper, for the first time, gives the mathematical model of the resonant transition during the dead time and thereby analyzes partial hard switching under different modulation schemes with consideration of transformer's parasitic capacitances. From the analysis of ZVS operation, the solution of splitting the interfacing inductance and placing them on both sides of the transformer is proposed and its associated methodology of selecting these inductances is introduced. It extends the ZVS for all the switching devices, therefore, enhance the efficiency or move losses away from the critical semiconductor devices. Finally, the theoretical analysis is verified by the experimental results from a 1 MHz Gallium Nitride (GaN) based DAB converter prototype.

4 February 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
YXYudi Xiao
Yudi Xiao
ZZZhe Zhang
Zhe Zhang
MDMartijn Sebastiaan Duraij
Martijn Sebastiaan Duraij
TZTiberiu-Gabriel Zsurzsan
Tiberiu-Gabriel Zsurzsan
Michael A.E. AndersenMichael A.E. Andersen
Michael A.E. Andersen
Power electronics converters operating at elevated temperature usually have degraded performance, such as reduced efficiency, lower noise immunity, and decreased system reliability, compared to those operating at room temperature. Nevertheless, harsh-environment applications, such as deep earth drilling, automotive, avionics, and space exploration, have been utilizing converters in high-temperature environments and are continuously pushing the temperature limits higher and higher with the advances in device technologies and converter design methodologies. This article starts with a literature study to identify the temperature dependence and the temperature limits of individual components. Then, published works about high-temperature converters are examined. Their selection of components is compared. Experimental results are analyzed to reflect on the efficacy of different component selections. Finally, since the latest published high-temperature converter was developed more than five years ago, a 1-kV input, 520-V output, 1-kW, $150$ °C-ambient-temperature-rated dc–dc converter is designed with state-of-the-art devices. Based on the literature review, and the test of the $150$ °C prototype, the main challenges of designing high-temperature power electronics converters are identified and concluded to be time-consuming, difficult, and expensive characterization of components, lack of accurate and computationally efficient models of converters, and optimizing component selection within short development time.

1 October 2016
Verified
Conference Paper
Open access
MXMao Xingkui
Mao Xingkui
HQHuang Qisheng
Huang Qisheng
KQKe Qingbo
Ke Qingbo
XYXiao Yudi
Xiao Yudi
ZZZhe Zhang
Zhe Zhang
Michael A.E. AndersenMichael A.E. Andersen
Michael A.E. Andersen
A high-efficiency photovoltaic (PV) micro-inverter consisting of two power stages i.e. a LLC resonant converter with a new hybrid control scheme and a dc-ac inverter is proposed, studied and designed in this paper. In the first power stage, the new hybrid control combining pulse-frequency modulation (PFM) and phase-shift pulse-width modulation (PS-PWM) is employed on a full-bridge LLC dc-dc converter, in order to achieve high efficiency when PV output voltage varies in a wide range. Moreover, a maximum power point tracking (MPPT) method based on power perturbation is implemented in the dc-ac inverter. Therefore, the complexity of regulating LLC converter can be reduced effectively, and efficiency optimal design can be carried out through the proposed designing procedure for the resonant tank of LLC converter. Finally, a prototype of the proposed PV micro-inverter (PVMI) is developed with rated power of 250W and output voltage of 220VAC/50Hz. The experiment shows that the peak efficiency of the PVMI is 95.5%, where efficiency of LLC converter is up to 97.7%, and the MPPT accuracy is more than 99%. Thus the validity of the proposed system structure, design and control method is verified.

5 February 2025 in IEEE Access
Verified
Journal Article
Open access
AEAbdelrahman Elwakeel
Abdelrahman Elwakeel
YLYuchuan Liao
Yuchuan Liao
YXYudi Xiao
Yudi Xiao
Rafael Pena-AlzolaRafael Pena-Alzola
Rafael Pena-Alzola
MZMin Zhang
Min Zhang
Weijia YuanWeijia Yuan
Weijia Yuan
To tackle emissions from the aviation industry and make it sustainable, research has been targeting electrifying aircraft. For this aim, articles have been focusing on how to replace regular jet engines with liquid hydrogen as fuel. This would be beneficial as hydrogen is expected to play a dual role, providing fuel for fuel cells to propel the aircraft electrically and to supply cooling to enable high-power density technologies such as superconducting machines and cryogenic power electronics circuits. However, using higher power density, especially cryogenic power electronics, can be challenging. This article investigates cryogenic power electronics for use on all-electric aircraft across different aspects, where it lays out how to integrate power electronics at cryogenic temperature into the architecture of the all-electric aircraft, how to use them with hydrogen fuel cells, and the voltage levels of the system. It reviews different semiconductor device technologies, circuit topologies, and passive devices to be used in power electronics circuitry, as well as logic circuits that are suitable for use at cryogenic temperatures. In addition, the article discusses the challenges of using semiconductor devices at such low temperatures, including the reliability, overall cooling, and recycling of hydrogen.

18 November 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
YXYudi Xiao
Yudi Xiao
ZZZhe Zhang
Zhe Zhang
KMKevin Tomas Manez
Kevin Tomas Manez
Michael A.E. AndersenMichael A.E. Andersen
Michael A.E. Andersen
In this paper, a universal power flow model for the Dual Active Bridge (DAB) based dc-dc converters with phase-shift modulation is derived. The model considers the lossy components, the dead time, and the resonant commutations of the converters. A power flow model for the Partial Parallel Dual Active Bridge (P2DAB) converter is generated from the universal power flow model. Based on the calculations, the power plateau phenomenon and the anti-power phenomenon, as well as their causes and influences are discussed. Because of the zero-reactive-power-loss in the lagging full-bridge, the zero-voltage-turn-on of all of the switches, and the zero-current-commutation of the switches in the lagging full-bridge during the power plateau, a hypothesis, which claims that the converter is more efficient in the power plateau operation than in other operation modes, is made. A laboratory prototype of the P2DAB converter is constructed. The analysis about the power plateau and the anti-power phenomenon is verified, as well as the proposed hypothesis is proved. Compared against the measured power, the model for the (P2DAB) converter has the maximum error less than 10%. Therefore, the validity of the universal power flow model is verified.