21 December 2020 in Nuclear Fusion
Future fusion reactors require a safe, steady state divertor operation. The required detached operation is, in tokamaks with metal walls, usually achieved by seeding of impurities, such as nitrogen. With strong seeding levels, the dominant radiation is emitted from a small, poloidally localized volume inside the confined region, in the vicinity of the X-point. The location of the radiating volume is observed to vary relative to the X-point depending on seeding and power levels, i.e. depending on the degree of detachment. At the ASDEX Upgrade tokamak, the position of the radiator relative to the X-point can be controlled in real time by a modulation of the nitrogen puff level. At a certain height of the radiator above the X-point, an ELM-suppressed regime is observed with minimal reduction of confinement. While the control of the X-point radiator already allows operation in full detachment at a dissipated power fraction of around 95 %, which is required for a future reactor and was previously never achieved in a controlled way, such an ELM-suppressed regime additionally eliminates the challenge of the transient, intolerably high heat fluxes by ELMs. Both requirements are met in the presented regime while maintaining a high energy confinement at high density.
1 March 2014 in Review of Scientific Instruments
In the ASDEX Upgrade tokamak, a radiation measurement for a wide spectral range, based on semiconductor detectors, with 256 lines of sight and a time resolution of 5μs was recently installed. In combination with the foil based bolometry, it is now possible to estimate the absolutely calibrated radiated power of the plasma on fast timescales. This work introduces this diagnostic based on AXUV (Absolute eXtended UltraViolet) n-on-p diodes made by International Radiation Detectors, Inc. The measurement and the degradation of the diodes in a tokamak environment is shown. Even though the AXUV diodes are developed to have a constant sensitivity for all photon energies (1 eV-8 keV), degradation leads to a photon energy dependence of the sensitivity. The foil bolometry, which is restricted to a time resolution of less than 1 kHz, offers a basis for a time dependent calibration of the diodes. The measurements of the quasi-calibrated diodes are compared with the foil bolometry and found to be accurate on the kHz time scale. Therefore, it is assumed, that the corrected values are also valid for the highest time resolution (200 kHz). With this improved diagnostic setup, the radiation induced by edge localized modes is analyzed on fast timescales.
10 March 2025 in Nuclear Fusion
Since the publication of the review Progress in the ITER Physics Basis (PIPB) in 2007, significant progress has been made in understanding the processes at the plasma-material interface. This review, part of the ITPA Nuclear Fusion Special Issue On the Path to Burning Plasma Operation, presents these developments, focusing on key areas such as the physics of plasma exhaust, plasma-material interactions, and the properties of plasma-facing materials and their evolution under plasma exposure. The coordinated efforts of the ITPA Topical Group on Scrape-Off Layer and Divertor Physics (DivSOL) have been instrumental in identifying and addressing critical research and development issues in numerous collaborative experimental and modelling projects.
30 January 2023 in Nuclear Materials and Energy
4 April 2023 in Physical Review Letters
We present a novel concept to tackle the power exhaust challenge of a magnetically confined fusion plasma. It relies on the prior establishment of an -point radiator that dissipates a large fraction of the exhaust power before it reaches the divertor targets. Despite the spatial proximity of the magnetic point to the confinement region, this singularity is far away from the hot fusion plasma in magnetic coordinates and therefore allows the coexistence of a cold and dense plasma with a high potential to radiate. In the compact radiative divertor (CRD) the target plates are placed close to this magnetic point. We here report on high performance experiments in the ASDEX Upgrade tokamak that indicate the feasibility of this concept. Despite the shallow (projected) field line incidence angles of the order of , no hot spots were observed on the target surface monitored by an IR camera, even at a maximum heating power of . And even with the point located exactly on the target surface and without density or impurity feedback control, the discharge remains stable, the confinement good (), hot spots absent, and the divertor in a detached state. In addition to its technical simplicity, the CRD scales beneficially to reactor-scale plasmas that would benefit from an increased volume of the confined plasma, more space for breeding blankets, smaller poloidal field coil currents, and—potentially—an increased vertical stability.
10 April 2025 in Plasma Physics and Controlled Fusion
TTthe EUROfusion Tokamak Exploitation Team
the EUROfusion Tokamak Exploitation Team
+65
JET returned to deuterium-tritium operations in 2023 (DTE3 campaign), approximately two years after DTE2. DTE3 was designed as an extension of JET’s 2022-2023 deuterium campaigns, which focused on developing scenarios for ITER and DEMO, integrating in-depth physics understanding and control schemes. These scenarios were evaluated with mixed D-T fuel, using the only remaining tritium-capable tokamak until its closure in 2023. A core-edge-SOL integrated H-mode scenario was developed and tested in D-T, showing good confinement and partial divertor detachment with Ne-seeding. Stationary pulses with good performance, no tungsten accumulation, and even without ELMs were achieved in D-T. Plasmas with pedestals limited by peeling modes were studied with D, T-rich, and D-T fuel, revealing a positive correlation between pedestal electron pressure and pedestal electron density. The Quasi-Continuous Exhaust regime was successfully achieved with D-T fuel, with access criteria similar to those in D plasmas. A scenario with full detachment, the X-point radiator regime, was established in D-T, aided by the real-time control of the radiator’s position. The crucial characterisation of tritium retention continued in DTE3, using gas balance measurements and the new LID-QMS diagnostic. Nuclear technology studies were advanced during the DTE3 campaign, addressing issues such as the activation of water in cooling loops and single event effects on electronics. Building on the previous D, T and DTE2 campaigns and the lessons learned from them, DTE3 extended our understanding of D-T plasmas, particularly in scenarios relevant to next-generation devices such as ITER and DEMO.