21 December 2020 in Nuclear Fusion
Future fusion reactors require a safe, steady state divertor operation. The required detached operation is, in tokamaks with metal walls, usually achieved by seeding of impurities, such as nitrogen. With strong seeding levels, the dominant radiation is emitted from a small, poloidally localized volume inside the confined region, in the vicinity of the X-point. The location of the radiating volume is observed to vary relative to the X-point depending on seeding and power levels, i.e. depending on the degree of detachment. At the ASDEX Upgrade tokamak, the position of the radiator relative to the X-point can be controlled in real time by a modulation of the nitrogen puff level. At a certain height of the radiator above the X-point, an ELM-suppressed regime is observed with minimal reduction of confinement. While the control of the X-point radiator already allows operation in full detachment at a dissipated power fraction of around 95 %, which is required for a future reactor and was previously never achieved in a controlled way, such an ELM-suppressed regime additionally eliminates the challenge of the transient, intolerably high heat fluxes by ELMs. Both requirements are met in the presented regime while maintaining a high energy confinement at high density.
11 January 2021 in Nuclear Fusion
TTthe EUROfusion MST1 team
+23
The Tokamak à Configuration Variable (TCV) tokamak is in the midst of an upgrade to further its capability to investigate conventional and alternative divertor configurations. To that end, modular and removable gas baffles have been installed to decrease the coupling between the divertor and the plasma core. The baffles primarily seek to suppress the transit of recycling neutrals to closed flux surfaces. A first experimental campaign with the gas baffles has shown that the baffled divertor remains compatible with a wide range of configurations including snowflake and super-X divertors. Plasma density ramp experiments reveal an increase of the neutral pressure in the divertor by up to a factor ×5 compared to the unbaffled divertor and thereby qualitatively confirm simulations with the SOLPS-ITER code that were used to guide the baffle design. Together with a range of new and upgraded divertor diagnostics, the baffled TCV divertor is now used to validate divertor models for ITER and next step devices with particular emphasis on geometric variations.
14 July 2017 in Plasma Physics and Controlled Fusion
The first results of particle-in-cell simulations of the electrostatic sheath and magnetic pre-sheath of thermionically emitting planar tungsten surfaces in fusion plasmas are presented. Plasma conditions during edge localized modes (ELMs) and during inter-ELM periods have been considered for various inclinations of the magnetic field and for selected surface temperatures. All runs have been performed under two assumptions for the sheath potential drop; fixed or floating. The primary focus lies on the evaluation of the escaping thermionic current and the quantification of the suppression due to the combined effects of space-charge and Larmor gyration. When applicable, the results are compared with the predictions of analytical models. The heat balance in the presence of thermionic emission as well as the contribution of the escaping thermionic current to surface cooling are also investigated. Regimes are identified where emission needs to be considered in the energy budget.
4 September 2019 in Nuclear Fusion
7 July 2023 in Nuclear Fusion
Using newly developed spectroscopic models to measure the divertor concentration of Ne and Ar, it is shown that the experimental detachment threshold on ASDEX Upgrade with Ar-only and mixtures of Ar+N or Ne+N scales as expected in comparison with an analytical equation derived by Kallenbach et al (2016 Plasma Phys. Control. Fusion 58 045013). However, it is found that Ar radiates more efficiently and Ne less efficiently in the scrape-off layer than the model predicts. By separately increasing the neutral beam injection power and cutting the impurity gas flow, it is shown that the partially detached and strongly detached X-point radiator scenarios reattach in ≈100 ms and ≈250 ms, respectively. The former timescale is set by the core energy confinement time, whereas the latter has an additional delay caused by the time required for the ionisation front to move from the X-point to the target. A simple equation with scalable geometric terms to predict the ionisation front movement time in future machines is proposed.
31 March 2020 in Nuclear Fusion