Fangyu Mao

Fangyu Mao

Auto-generated profile, based on publicly available information

Fangyu Mao

University of Macau

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 July 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
FMFangyu Mao
Fangyu Mao
YLYan Lu
Yan Lu
RMRui P. Martins
Rui P. Martins
This paper presents a reconfigurable cross-connected (CC) wireless power transceiver (TRX) operating at 6.78 MHz and implemented for bidirectional device-to-device (D2D) charging with high efficiency and small system volume. We propose, for the first time, a CC topology applied to a differential class-D power amplifier for significant switching loss reduction. Two delay-locked loops (DLLs) for each power NMOS transistor form the reconfigurable controller, realizing the adaptive deadtime control in the transmitter (TX) mode and the off-delay compensation in the receiver (RX) mode, leading to high power conversion efficiency and safe operation. To realize the inductive load for the TX mode in the whole coupling range at the resonant frequency, we use an on-chip tunable capacitor. Furthermore, we also study the power link efficiency in the D2D direct charging system and verify that the near-maximum power link efficiency can be inherently achieved in this scenario. The proposed wireless power TRX, fabricated in a 0.35-μm CMOS process with 5-V devices, measured a peak D2D total efficiency of 77.2% when the output power is 0.7 W. The maximum charging power is 2.74 W with a total efficiency of 62.7% and the maximum transmission distance is 24 mm, both measured.

10 July 2020 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
XLXiaofei Li
Xiaofei Li
FMFangyu Mao
Fangyu Mao
YLYan Lu
Yan Lu
RMRui P. Martins
Rui P. Martins
Tiny implantable medical devices in millimeter size demand advanced wireless power solutions that operate at hundreds of megahertz and mainly use passive rectifiers for ac-dc power conversion. A conventional cross-connected (CC) rectifier can operate with high frequency and low input voltage but only achieves good efficiencies in a very narrow input power range, due to the shoot-through and reverse currents. This work presents a CMOS passive rectifier with active bias tuning (ABT), allowing a widely extended input range with high power conversion efficiency (PCE). In addition, we compensate for the process, voltage, and temperature variations with the ABT scheme that leads to a robust design for very-high-frequency (VHF) operation. Meanwhile, we propose a peak VOUT searching scheme to indicate the charging/discharging directions for the ABT. We obtain a bias-voltage balancing among stacked rectifier stages with a switched-capacitor network. The proposed rectifier is fabricated in a 65-nm CMOS process. Measurement results of three chips show that the proposed rectifier improves the PCE over a wide input range, with an average maximum PCE of 64.4%.

9 March 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
FMFangyu Mao
Fangyu Mao
YLYan Lu
Yan Lu
EBEdoardo Bonizzoni
Edoardo Bonizzoni
FBFilippo Boera
Filippo Boera
MHMo Huang
Mo Huang
RMRui P. Martins
Rui P. Martins
This article presents a hybrid single-inductor bipolar-output (SIBO) dc-dc converter for active-matrix organic light-emitting diode (AMOLED) displays, which are relatively more sensitive to the supply noise on the positive supply. First, to improve the display quality we adopt a floating negative output configuration to migrate all the switching ripples into the negative output, achieving a near-zero voltage ripple on the positive output. Second, we design low-power shunt regulators, which only deal with a small portion of the output ripple, to regulate the positive output voltage further, improving the load transient response. Besides, the hybrid topology and the proposed cross-coupled bootstrap-based level-shifter, with a dual-PMOS inverter buffer, only uses standard CMOS devices without deep-n-well, reducing the chip area and cost. The proposed converter, implemented in 0.35- μm CMOS with 5-V devices, operates at 1 MHz, leading to a measured positive output voltage ripple lower than 1 mV (all conditions). It achieves a measured 3-mV undershoot voltage and, an unnoticeable overshoot voltage on the positive output, when the output current varies between 30 and 350 mA. The measured peak power efficiency is 89.3% at 1.1-W output power. The maximum output power is 3.5 W.

6 October 2022 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
FMFangyu Mao
Fangyu Mao
YLYan Lu
Yan Lu
FMFranco Maloberti
Franco Maloberti
RMRui P. Martins
Rui P. Martins
This paper presents a hybrid single-inductor bipolar triple-output (SIBTO) DC-DC converter for active-matrix organic light-emitting diode (AMOLED) displays. Generating the bipolar rails $V_{\mathrm{OP}}$ and $V_{\mathrm{ON}}$ for the pixel array and the analog rail AV $_{\mathrm{DD}}$ for the source driver with a single inductor greatly reduces the system size and cost. This work adopts the floating negative output topology for an ultra-clean positive output. In addition, we propose a push-pull charge balancer to compensate and regulate the $V_{\mathrm{OP}}$ , improving the line and load regulation with continuous currents and acceptable power consumption. This work also proposed a slow-comparator based ordered power distributive control (SC-OPDC) to regulate the AV $_{\mathrm{DD}}$ with a pulse-skipping scheme to reduce the power loss. The designed power transistor buffers with adaptive deadtime control improve power conversion efficiency and decrease the required minimum load current of AV $_{\mathrm{DD}}$ . The proposed SIBTO converter, implemented in 0.18- $\mu $ m BCD process, operates at 1.67 MHz. It achieves a peak efficiency of 94.1% at 0.88 W output and a maximum output power of 3.67 W with an efficiency of 87%. The maximum output voltage ripples are 5 mV, 17 mV, and 7.5 mV for $V_{\mathrm{OP}}$ , $V_{\mathrm{ON}}$ , and AV $_{\mathrm{DD}}$ , respectively.

17 May 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
Fen XiaFen Xia
Fen Xia
FMFangyu Mao
Fangyu Mao
YLYan Lu
Yan Lu
Mohamad SawanMohamad Sawan
Mohamad Sawan
Inductive link intended to deliver energy to implantable devices is recently becoming a popular method. To improve link efficiency, the compensated capacitors are adopted to resonate at the same frequency with the power transfer frequency on both sides. However, there is limited research on link efficiency and output power concerning quality factors, the selection between serial–parallel (SP) and serial–serial (SS) topologies, as well as coil design. This study delves into the efficiency of SP and SS topologies using rigorous mathematical derivations with reflected impedance models in terms of quality factors. It introduces a selection factor to help choose topology based on link efficiency. Results show that SS is better when the load quality factor ( $Q_{L}$ ) is lower than the selection factor, and vice versa. The study also examines the performance limits of both topologies concerning frequency, inductance, and load impedance. It proposes a specific $Q_{L}$ for maximum efficiency and a coil design procedure considering specific absorption rate limitations. By leveraging simulations and the design procedure, the study manufactures a pair of flexible coils for biomedical use. The designed link achieves a 62.99% efficiency under a 500 $\Omega$ load, with an overall efficiency of 46.96% including a passive rectifier.

23 February 2022 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
FMFangyu Mao
Fangyu Mao
YLYan Lu
Yan Lu
RMRui P. Martins
Rui P. Martins
This article proposes a reconfigurable single-stage regulating asymmetrical full-wave step-down rectifier (SDR) for fast wireless charging. The SDR is reconfigurable into a step-up power amplifier (SUPA) for device-to-device (D2D) wireless charging. The SDR and SUPA can have a direct connection with the battery without an additional voltage regulator module (VRM). With the single-stage structure, the transmitting (TX) and receiving (RX) ac voltages across the resonant coil can be boosted, which greatly reduces the coil currents and losses, improving the D2D charging power. A reconfigurable controller for the TX/RX mode selection, as well as the switching timing control, is designed. The chip is fabricated in 0.35- $\mu \text{m}$ CMOS that contains 20-V devices. For the asymmetrical operation, one GaN device is used for the high current path. Also, zero-voltage switching (ZVS) is realized for all the power transistors with one small (180 nH in the 4015 package) power inductor. The bidirectional D2D WPT system achieves a maximum charging power of 5.1 W with a D2D total efficiency of 46.3% and a charging distance of 1.6 cm. Finally, the peak total efficiency is 51.4% with a charging power of 3.4 W and a charging distance of 1 cm.