19 August 2019 in IEEE Transactions on Power Electronics
Medium-voltage high-speed drive is promising in applications, such as the centrifugal compressors and electrified transportation. However, it raises lots of design challenges for the converters, which drive the motors. A SiC and Si hybrid ANPC converter is developed to address these challenges. In this article, the essence of this hybrid structure is investigated to clearly show the derivation process of the hybrid active neutral-point-clamped (ANPC) converter and inspire future research on these hybrid topologies. A dedicated space vector modulation (SVM) scheme is proposed for the hybrid ANPC converter, which enables the three-phase hybrid ANPC converter operating with SiC mosfets in high frequency and Si IGBTs in fundamental frequency. A neutral point (NP) voltage balancing scheme is added to the SVM scheme to balance the NP voltage imbalance under low-frequency modulation index. All these efforts make the hybrid ANPC converter become a high power density and fairly low-cost solution. A 400 Hz fundamental frequency, 3.6 kHz switching frequency, medium-voltage high-speed drive system is assumed and tested by the scaled-down experimental results. The effectiveness of the proposed SVM and NP voltage balancing method have both been verified.
19 August 2019 in IEEE Transactions on Power Electronics
The thermal management plays an important role in improving the reliability and lifetime of high power converters, especially for the high voltage direct current (HVdc) transmission system. In the voltage source converter based HVdc systems (VSC-HVdc), the hybrid modular multilevel converters (MMCs) are taken as the excellent candidates due to their dc short-circuit fault ride-through ability and less submodule (SM) devices. Furthermore, the voltage modulation index of hybrid MMCs can be promoted to achieve higher power rating and efficiency. However, in this article, it is revealed that thermal stress distribution inside the SMs becomes more unbalanced under a high voltage modulation index, which would lead to serious thermal fatigue. To overcome this problem, the active bypass with thyristor for half-bridge submodules (HBSMs) and symmetrical modulation for full-bridge submodules (FBSMs) based active thermal control strategies are employed. With the presented thermal control strategies, the junction temperature of the most stressed devices in both HBSMs and FBSMs is reduced enormously. Besides, the thermal control strategy does not bring negative influence on the steady-state output performance of hybrid MMC. Finally, the theoretical analysis and effectiveness of the proposed control methods are verified based on a laboratorial MMC prototype.
10 June 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The thermal design of highly reliable modular multilevel converters (MMCs) is significant for the voltage-source-converter based high-voltage direct current (VSC-HVDC) systems, especially under the AC unbalanced fault. In this paper, the surplus sub-module is employed as a new control freedom to optimize the thermal behavior of MMCs, because its number is linearly increased with the AC voltage dip. With the surplus sub-module active bypassed (SSAB), the total sub-modules of MMC in one arm can be taken turns to reduce the thermal stress of the hottest power device. In order to obtain equal AC voltages in three phases to improve the SSAB strategy, the neutral-point-shift (NPS) scheme is introduced under the unbalanced conditions, especially single-phase-to-ground fault. Through balancing the amplitude of MMC AC voltages with the NPS scheme, the thermal stress asymmetry of MMC under the single-phase-to-ground fault is mitigated and the junction temperature of the most stressed power devices is significantly reduced. Finally, the simulation and experiment results show that the junction temperature rise of the most stressed power device is reduced by nearly 30% with the SSAB plus NPS scheme.
31 May 2019 in IEEE Microwave and Wireless Components Letters
A new balanced-to-balanced (BTB) rat-race coupling network is presented. The theoretical analysis is performed based on equivalent circuits and design equations are derived to achieve the functions of differential-mode (DM) power division, DM impedance match, common-mode (CM) suppression, and port isolation. The design theories are well vindicated by an exemplary BTB rat-race coupling network centered at 1.8 GHz with a compact size of 0.21λg². The simulated and measured results agree well.
22 May 2019 in IEEE Transactions on Microwave Theory and Techniques
In this paper, a new method to develop balanced-to-unbalanced (BTU) filtering out-of-phase power divider (PD) is presented. Based on the comparison between BTU filtering out-of-phase PD and balanced-to-balanced (BTB) filter, it is found that the BTU filtering out-of-phase PD can be constructed by combining a BTB filter and an additional parallel four-port network. The design equations are derived and corresponding circuit models are given. Finally, a prototype is designed to verify the theoretical prediction. The design procedure and parameter selection are detailed. The good performance and the consistency between the simulated and measured results verify the design theory.
24 August 2012 in Microwave and Optical Technology Letters