Florian Josef Günter

Florian Josef Günter

Auto-generated profile, based on publicly available information

Florian Josef Günter

Institute for Machine Tools and Industrial Management, Technical University of Munich, D-85748 Garching, Germany

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 May 2019 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
FGFlorian J. Günter
Florian J. Günter
CBClemens Burgstaller
Clemens Burgstaller
FKFabian Konwitschny
Fabian Konwitschny
GRGunther Reinhart
Gunther Reinhart
In the production process chain of lithium-ion battery cells, the filling process is eminent for the final product quality and costs. The filling consists of several dosing steps of electrolyte liquid into the cell and the subsequent (intermediate) wetting of the cell components. The quantity of electrolyte filled not only has an impact on the wetting rate of electrodes and separator but also limits the capacity of the cell and influences the battery lifetime. However, too much electrolyte is dead weight, results in a lower energy density and unnecessarily increases the costs of the battery. To ensure low costs in production and at the same time high quality of the cells, the optimal amount of electrolyte is studied in this paper. Based on experimental data from electrochemical impedance spectroscopy, the filling process, the formation process as well as a lifetime test, the interdependencies between electrolyte quantity, wetting rate, capacity, energy density and lifetime are presented for large-format cells.

17 October 2018 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
FGFlorian J. Günter
Florian J. Günter
JHJan Bernd Habedank
Jan Bernd Habedank
DSDavid Schreiner
David Schreiner
TNTobias Neuwirth
Tobias Neuwirth
RGRalph Gilles
Ralph Gilles
GRGunther Reinhart
Gunther Reinhart
In the production process chain of lithium-ion battery cells, the filling, consisting of dosing and wetting steps, of the cell and its components with electrolyte liquid is eminent for the final product quality and costs. To reduce the unnecessary wetting duration between filling and formation, and thereby the production costs, a measurement method for the wetting progress is necessary. In this paper, electrochemical impedance spectroscopy (EIS) as a well-established technique is used for the first time to quantify the wetting degree of batteries during cell production. The experimental data of the EIS acquired during the dosing and subsequent wetting process is correlated to images recorded by in situ neutron radiography. Results show that the impedance of the battery cells strongly depends on the wetting degree of the cell assembly and can thus be used to determine the fully wetted state enabling faster processing.

6 February 2019 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
JHJan Bernd Habedank
Jan Bernd Habedank
FGFlorian J. Günter
Florian J. Günter
NBNicolas Billot
Nicolas Billot
RGRalph Gilles
Ralph Gilles
TNTobias Neuwirth
Tobias Neuwirth
MZMichael F. Zaeh
Michael F. Zaeh

1 March 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
FGF. J. Günter
F. J. Günter
NWN. Wassiliadis
N. Wassiliadis
A large-format pouch cell with a nominal capacity of 78 Ah from the Volkswagen ID.3 was disassembled and analyzed to characterize the state of the art of industrial-scale cells in automotive applications. The cell components were separated from each other, geometrically measured, and weighed to quantify the volume and weight fractions from electrode to cell level. Material samples from the electrodes were characterized by scanning electron microscopy (SEM), elemental analysis, and mercury porosimetry. Half cells were built post mortem and assessed in electrochemical tests. The results revealed a stacked cell of laminated electrode layers. The cathode showed a bi-modal particle distribution and its active material ranged with LiNi0.65Mn0.2Co0.15O2 in between NMC622 and NMC811. Silicon-free graphite was used as the anode active material. Over 75% of the cell mass and over 81% of the cell volume directly contribute with its active material to the specific energy of 268 Wh kg−1 and energy density of 674 Wh L−1 at cell level. 91% of the anode and 93% of the cathode were utilized in the pristine cell, respectively. In charge rate tests, the anode was identified as the limiting electrode. The results provide valuable insights into the state of the art of automotive lithium-ion batteries and serve as a reference for scientific research.

1 October 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
SGSophie Grabmann
Sophie Grabmann
JKJohannes Kriegler
Johannes Kriegler
FHFelix Harst
Felix Harst
FGFlorian J. Günter
Florian J. Günter
MZMichael F. Zaeh
Michael F. Zaeh
The qualification of production systems that enable reliable and stable production processes is a major challenge in manufacturing large-format lithium-ion batteries. During cell assembly, the electrode sheets of the anode and the cathode are stacked, and are electrically contacted by a welding process. It was shown that laser beam welding employing a beam source in the green wavelength range is a promising joining approach in terms of high productivity. Therefore, the influence of the process parameters, such as the laser power, the welding speed, the pulse frequency, and the pulse duration, on the weld seam quality was investigated. Particular emphasis was placed on the mechanical strength of the weld seam. Statistically planned experiments were used to determine feasible parameter sets for welding the most common current collectors of lithium-ion battery electrodes, copper (Cu), and aluminum (Al). The influence of the individual process parameters on the tensile shear force was evaluated. Stacks of 40 metal foils were welded with a thin metal sheet in lap joint configuration. Based on an analysis of the requirements for minimum mechanical seam strengths, this study confirms that laser beam welding using a green high-power disk source is an auspicious process for the internal contacting of lithium-ion batteries.

1 March 2021 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
DSDavid Schreiner
David Schreiner
TZTanja Zünd
Tanja Zünd
FGFlorian J. Günter
Florian J. Günter
LKLudwig Kraft
Ludwig Kraft
BSBenedikt Stumper
Benedikt Stumper
HGHubert A. Gasteiger
Hubert A. Gasteiger
A lithium- and manganese-rich layered transition metal oxide (LMR-NCM) cathode active material (CAM) is processed on a pilot production line and assembled with graphite anodes to ≈7 Ah multilayer pouch cells. Each production step is outlined in detail and compared to NCA/graphite reference cells. Using laboratory coin cell data for different CAM loadings and cathode porosities, a simple calculation tool to extrapolate and optimize the energy density of multilayer pouch cells is presented and validated. Scanning electron microscopy and mercury porosimetry measurements of the cathodes elucidate the effect of the CAM morphology on the calendering process and explain the difficulty of achieving commonly used cathode porosities with LMR-NCM cathodes. Since LMR-NCMs exhibit strong gassing during the first cycles, a modified formation procedure based on on-line electrochemical mass spectroscopy is developed that allows stable cycling of LMR-NCM in multilayer pouch cells. After formation and degassing, LMR-NCM/graphite pouch cells have a 30% higher CAM-specific capacity and a ≈5%–10% higher cell-level energy density at a rate of C/10 compared to NCA/graphite cells. Rate capability, long-term cycling, and thermal behavior of the pouch cells in comparison with laboratory coin cells are investigated in Part II of this work.