Sanghyun Park

Sanghyun Park

Auto-generated profile, based on publicly available information

Sanghyun Park


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 April 2024 in Optics and Lasers in Engineering
Verified
Journal Article
Open access
GLGeonhui Lee
Geonhui Lee
SPSanghyun Park
Sanghyun Park
HJHanjin Jo
Hanjin Jo
SHSeungjin Hwang
Seungjin Hwang
SLSungyoon Lee
Sungyoon Lee
TYTae Jun Yu
Tae Jun Yu

30 April 2022 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
DPDaewong Park
Daewong Park
SLSungyoon Lee
Sungyoon Lee
SHSeungjin Hwang
Seungjin Hwang
GLGeonhui Lee
Geonhui Lee
Hanjin JoHanjin Jo
Hanjin Jo
TYTae Jun Yu
Tae Jun Yu
This study introduces laser surface modification technology using a 532 nm Nd:YAG nanosecond laser. A laser beam homogenizer was used to spatially homogenize the laser beam into a square shape with an interference pattern of 30 μm. For laser surface modification processing, primary processing under 110 conditions was first performed, and then, 15 types of main processing conditions were determined based on the three-dimensional surface structure of laser surface modified zircaloy-4. Subsequently, the specimen was post-processed using three methods: left in the air (25 ℃), heated in the oven (200 ℃ for 2 h), and boiled in water (100 ℃ for 2 h). In the absence of post-processing or with heat post-processing, the laser surface modified zircaloy-4 showed super hydrophobicity with a contact angle of 150° or higher for specific laser surface processing parameters. Under specific laser surface processing conditions, the laser surface modified zircaloy-4 with boiling water post-processing exhibited properties close to super hydrophilic with a contact angle of less than 5°. It was confirmed that the surface wettability of zircaloy-4 can be controlled using a spatially shaped nanosecond laser beam.

1 November 2026 in Journal of Laser Applications
Verified
Journal Article
Closed access
SPSanghyun Park
Sanghyun Park
SKSion Kim
Sion Kim
SLSungyoon Lee
Sungyoon Lee
DSDuckbong Seo
Duckbong Seo
HKHong Jin Kong
Hong Jin Kong
TYTae Jun Yu
Tae Jun Yu
This study examined through-thickness cutting of 110-mm-thick SUS304–SS400 clad steel (10 mm SUS304/100 mm SS400) using a 6-kW laser oxy-fuel and oxy-flame hybrid (LOXAFH) process. With SUS304 facing the cutting head, oxy-fuel heating formed no measurable entrance kerf. Three laser-assisted oxygen cutting (LASOX) trials failed to penetrate at 6 kW, 0.70 MPa(g) cutting-oxygen pressure, 50 mm min−1, and 10 mm standoff distance. At the same principal settings, one LOXAFH trial achieved full penetration with an O2–liquefied petroleum gas flame and approximately 30 s of stationary preheating. Two additional LOXAFH trials produced through cuts at selected settings. Across these three cuts, top and bottom kerf widths were 6.80–7.75 and 9.55–10.38 mm, respectively. At otherwise nominally identical LOXAFH settings, one 6-kW trial penetrated, whereas eight 3-kW trials failed. At 3 kW, three SS400-up trials penetrated, while eight SUS304-up trials failed. These comparisons indicate that laser power and incident material affected penetration. The matched LASOX–LOXAFH comparison supports feasibility, but the effects of stationary preheating and continuous flame assistance could not be separated. Improved oxygen access remains a possible explanation because in-kerf flow and cut-front motion were not measured. Repeatable penetration was observed at selected conditions, but repeatability at a fixed successful setting for the standard SUS304-up plate remains unverified. Comprehensive cut-quality assessment and suitability for nuclear dismantling require further evaluation.