Shao-Hua Ma

Shao-Hua Ma

Auto-generated profile, based on publicly available information

Shao-Hua Ma

School of Instrument Science and Opto-electronic Engineering, Hefei University of Technology, Hefei, China

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 September 2025 in IEEE Sensors Journal
Verified
Journal Article
Closed access
YSYi Shen
Yi Shen
SMShao-Hua Ma
Shao-Hua Ma
YLYu-Wei Liu
Yu-Wei Liu
ZCZhen–Ying Cheng
Zhen–Ying Cheng
Qiaosheng PanQiaosheng Pan
Qiaosheng Pan
RLRui-Jun Li
Rui-Jun Li
Micro–nano probes are crucial components of micro/nano coordinate measuring machines. Most probes rely on low-stiffness elastic mechanisms, resulting in prolonged settling times and large dynamic errors. A micro–nano probe with low stiffness and high dynamic performance based on an eddy current damper (ECD) was developed to address these issues. The probe’s dynamic performance optimization was achieved through comprehensive static and dynamic analyses. The design and optimization of the ECD were carried out through theoretical modeling and simulation analysis. Experimental results indicate that the stiffness of the optimized probe remains almost unchanged, with an average horizontal stiffness of 0.711 mN/μm and a vertical stiffness of 0.258 mN/μm. The settling time is reduced by approximately 90% to less than 1.0 s. The proposed probe, characterized by its low stiffness and high dynamic performance, meets the high-precision and high-efficiency measurement requirements for micro components.

7 July 2025 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
SMShao-Hua Ma
Shao-Hua Ma
KJKai Jiang
Kai Jiang
ZCZhen–Ying Cheng
Zhen–Ying Cheng
RLRui-Jun Li
Rui-Jun Li
MCMeng-Ting Cheng
Meng-Ting Cheng
The assembly accuracy of motion axis of machine tool is determined by multi parameters, including geometric errors of linear guides and parallelism between multi axis, named error equalization effect. This article proposes a multi-functional laser calibrator, which is consisted of a novel five degree of freedom measurement (5-DOFM) system and a dual-axis precision level with a pentagonal prism. The geometric errors of linear guide (including straightness errors, pitch, yaw and roll angular errors) and parallelism between multi axis could be detected conveniently. Especially, the influence of the pentagonal prism on parallelism measurement was investigated and proved using reflection matrices. A series of validation experiments were conducted to demonstrate the effectiveness of laser calibrator. The experiments results reveal that designed laser calibrator can achieve measurement range of ± 150 um for straightness errors detection, and ± 200″ for angular errors detection. The measurement error of parallelism between multi guide rails can be controlled less than 1″ (5 um/m) according the analysis results of the pentagonal prism. The proposed instrument can provide numerical reference for the research of motion axis error equalization effect and the improvement of assembly accuracy.

30 July 2025 in IEEE Sensors Journal
Verified
Journal Article
Closed access
WFWan Fang
Wan Fang
YWYong-Jun Wang
Yong-Jun Wang
Liying LiuLiying Liu
Liying Liu
SMShao-Hua Ma
Shao-Hua Ma
Xiaojuan MoXiaojuan Mo
Xiaojuan Mo
RLRui-Jun Li
Rui-Jun Li
A novel design method based on topology optimization is proposed and demonstrated to enhance thermal stability in laser four-degree-of-freedom (4-DOF) measurement systems against environmental temperature fluctuations. The overall thermal deformation of the measurement systems is calculated by finite element analysis. The thermal errors caused by thermal deformation of workpieces are analyzed and modeled. The workpieces of the 4-DOF measurement systems are designed using topology optimization, resulting in a 50% reduction in thermal deformation. Furthermore, the temperature field of the measurement system is optimized by incorporating thermal insulation materials, and stability experiments are performed on the system both before and after optimization. The stability of the laser beam is improved by 53.9%, 49.0%, 58.0%, and 52.5% in two angular and two straightness directions, respectively. Experimental results demonstrate that the proposed method effectively enhances the stability of the 4-DOF measurement systems and can be applied to improve the thermal stability of other precision instruments.