16 October 2020 in Journal of Applied Physics
The crystallization process of melt quenched Ge-rich GeSbTe films, with composition optimized for memory applications, has been studied by optical reflectance measurements. The optical properties have been related to the structure and composition by means of the effective medium approximation. The compositional variations have been investigated by transmission electron microscopy and electron energy loss spectroscopy. Amorphous materials prepared by melt-quenching with different laser energy densities have been studied. For the energy density of 1.5 J cm−2, a uniform amorphous layer, with embedded Ge crystalline grains, is obtained. The film exhibits a crystallization temperature of 275 °C and no relevant phase separation during crystallization. For a lower energy density of 1 J cm−2, only half of the film thickness is quenched to the amorphous phase, with Ge depletion. The crystallization temperature of the Ge depleted film is 245 °C, and a partial phase separation occurs.
23 September 2005 in Acta crystallographica Section B, Structural science, crystal engineering and materials
In a system consisting of two different lattices, structural stability is ensured when an epitaxial relationship occurs between them and allows the system to retain the stress whilst avoiding the formation of a polycrystalline film. The phenomenon occurs if the film thickness does not exceed a critical value. Here we show that in spite of its orthorhombic structure, a 14 nm-thick NiSi layer can three-dimensionally adapt to the cubic Si lattice by forming transrotational domains. Each domain arises by the continuous bending of the NiSi lattice, maintaining a close relationship with the substrate structure. The presence of transrotational domains does not cause a roughening of the layer, but instead it improves the structural and electrical stability of the silicide in comparison with a 24 nm-thick layer formed using the same annealing process. These results have relevant implications for the thickness scaling of NiSi layers which are currently used as metallizations of electronic devices.
1 May 1998 in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
The thermal stability of thin cobalt silicide layers grown on preamorphized chemical vapor deposited silicon layers has been studied in the temperature range between 950 and 1100 °C. The morphology of the starting layers and their evolution during the thermal processes was analyzed by transmission electron microscopy, atomic force microscopy and Rutherford backscattering spectroscopy. The observed increase in sheet resistance with the annealing time has been correlated to the agglomeration process taking into account the dependence of the resistivity on film thickness and carrier mean free path. Sheet resistance measurements have been used to study the agglomeration process of CoSi2 by varying temperature and substrate doping (As, BF2, and Si implants). The process is thermally activated with an activation energy of 4.3 eV for the Si implanted samples. The BF2 implanted substrate show a higher activation energy (∼5.4 eV), while the arsenic implanted a lower one (∼3.6 eV). This difference is attributed to the weakening of the Co–Si bonds by arsenic atoms and to the presence of some fluorine precipitates at the CoSi2/Si interface that increase the energy needed for the reaction at the silicide/silicon interface.
15 April 2001 in Journal of Applied Physics
Low-temperature photoluminescence (PL) spectroscopy, in conjunction with transmission electron microscopy (TEM) and optical microscopy (OM) have been carried out to investigate the origin of radiative recombination from various extended defects that evolve during high-temperature processing of ion-implanted epitaxial silicon. From PL studies on samples, we provide spectroscopic evidence of precipitation of the implanted impurities well below the solid-solubility limit. This result is being supported by observations from secondary ion mass spectrometry and spreading resistance profiling of the implanted ions. Cross sectional TEM analyses on these samples reveal 〈111〉-oriented precipitates located in a region containing a high dislocation density. Postimplantation annealing in oxygen ambient results in the formation of dislocations and oxidation-induced stacking faults (OISF). A systematic analysis of PL spectra on different-implanted and preannealed samples, in conjunction with TEM and OM analyses, reveals that the conventionally observed dislocation-related D1 and D2 lines in the PL spectrum is not a characteristic of the OISF, but of the dislocations only. It is shown that the OISF acts as a nonradiative channel for luminescence in silicon. Various other sources of nonradiative channels in silicon are also presented and the efficacy of photoluminescence technique in the characterization of process-induced defects in silicon is discussed.
1 December 1995 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
1 March 1995 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms