15 January 2007 in Journal of Materials Chemistry
We report the fabrication of solution-processable organic thin-film transistors (OTFTs) based on poly(9,9′-dioctylfluorene-alt-bithiophene) (F8T2) doped with an electron-acceptor, 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ). The 8% doping of the F8T2 film was found to result in an increased hole mobility, up to 0.01 cm2 V−1 s−1, and in an improved on/off ratio, as well as in a low off-current, of the order of 10−11 A. The doped F8T2 device was also found to exhibit a better threshold voltage and reduced hysteresis behavior. These improvements in performance are attributed to the formation of the F8T2-F4TCNQ complex, which results in better hole injection and improved device stability.
10 January 2015 in Electronic Materials Letters
14 April 2005 in ETRI Journal
Alkoxy-substituted poly(spirobifluorene)s and their copolymers with a triphenylamine derivative have been synthesized by Ni(0)-mediated polymerization. The polymers were well soluble in common organic solvents. Pure blue-light emissions without the long wavelength emission of poly(fluorene)s have been observed in the fluorescence spectra of polymer thin films. The light emitting diodes with a device configuration of ITO/PEDT:PSS(30 nm)/polymer(60 nm)/LiF(1 nm)/Al(100 nm) have been fabricated. The electroluminescence spectra showed the blue emissions without the long wavelength emission as observed in the fluorescence spectra. The relatively poor electroluminescence quantum yield of the homopolymer (0.017% @ 20 mA/cm2) with color coordinates of (0.16, 0.07) has been improved by the introduction of triphenylamine moiety, and the copolymer with triphenylamine derivative exhibited an electroluminescence quantum yield of 0.15 % at 20 mA/cm2 with color coordinates of (0.16, 0.08). Moreover, the introduction of polar side chains to the spirobifluorene moiety enhanced the device performance and led to the quantum yields of 0.6 to 0.7 % at 20 mA/cm2, although there was some expense of color purities.
10 January 2014 in Electronic Materials Letters
1 April 2013 in Journal of the Korean Physical Society
We investigated the incorporation of Ga into zinc-tin-oxide (ZTO) thin-film transistors (TFTs) and assessed the TFTs’ electrical and stability properties. The Ga-doped ZTO (ZTO:Ga) thin films were deposited on thermally oxidized silicon substrates by using a sol-gel technique. The Ga contents were varied from 1 to 20 atomic percent (at.%) while the Zn:Sn ratio was maintained at 1:1. The dependence of the ZTO:Ga thin films’ structural properties on the Ga content was analyzed using Xray diffraction (XRD) spectra, scanning probe microscopy (SPM), X-ray photoelectron spectroscopy (XPS), and UV-visible spectrophotometry. The field effect mobilities and the I on /I off ratios of the ZTO:Ga-TFTs were between 0.68 and 2.95 cm2Vs−1s−1 and ∼104 and ∼106, respectively. At low Ga contents, the (<10-at.%) TFTs displayed similar TFT parameters, but the 20-at.%-Ga TFT showed improved mobility and stability characteristics. Moreover, the 20-at.%-Ga thin film had a smoother surface and increased crystallinity than the low Ga-content samples did.
11 June 2012 in Journal of Materials Chemistry
A material approach to fabricating high-performance nonstick molds for manufacturing ultrahigh-resolution features (92% at 365 nm), high modulus and wide-range modulus tunability (0.757–4.192 GPa), high resistance to organic solvents (<1.2 wt%), low shrinkage (<3%), and high water contact angle (91–103°). The Si-SSQA–acrylic blends with a nonstick property were easily transferred to high-resolution replica molds with sub-25 nm features, a pitch of 25 nm and a height of 100 nm, even if the release agent was not modified onto the master. In addition, nonstick replica molds with a low concentration of uncross-linked (meth)acrylate showed the ability to duplicate ultrasmall nanostructures with a sub-8 nm parallel line, a pitch of 17 nm and a height of 6–7 nm. Furthermore, the Si-SSQA-based replica mold prevented the formation of bubble defects during imprinting owing to sufficient gas permeability.