Universiti Malaysia Perlis, Center of Excellence Geopolymer & Green Technology (CeGeoGTech), Kompleks Pusat Pengajian Jejawi 2, Taman Muhibbah, 02600 Jejawi, Arau, Perlis, Malaysia
Auto-generated profile, based on publicly available information
Muhammad Salihin Zakaria
Universiti Malaysia Perlis, Center of Excellence Geopolymer & Green Technology (CeGeoGTech), Kompleks Pusat Pengajian Jejawi 2, Taman Muhibbah, 02600 Jejawi, Arau, Perlis, Malaysia
A formula for making paint was developed using waste expanded polystyrene foam (EPS) as a binder. This method replaces the alkyd resin in most commercial paint, which is derived from the byproducts of refining crude oil. Experimental results showed that 27% waste polystyrene foam can be incorporated in the paint formulation. Basic performance tests for EPS paint were conducted and evaluated, and the developed formulation was compared with commercial paint containing modified alkyd resin as a binder. Test results showed that EPS-based paint has some advantages such as excellent abrasion resistance, water resistance, alkali resistance, hardness, and adhesion characteristics.
1 January 2022 in Journal of Physics: Conference Series
The insulating nature of a polymer can be changed to electrically conductive by incorporating conductive fillers within the polymer matrix to form a conductive polymer composite (CPC). One of the potential application of CPCs are in the area of flexible electronic interconnect application. Nevertheless, the correlation between the electrical conductivity and mechanical properties of CPCs such as tensile was found to be limited. Therefore, this paper is aimed to report the preliminary investigation on the correlation between conductivity and mechanical properties of a low-density polyethylene (LDPE) incorporation with conductive filler which is carbon black (CB. It was observed that the tensile strength was decreased by up to 29.4% and the elongation of break was decreased by up to 90.6% at higher CB loading compared to pure LDPE. Nonetheless, the modulus of elasticity and the electrical conductivity of the composites were increased by up to 150.5% and 16.4% at higher CB loading respectively. Moreover, it was found that the effect of CB additions on the tensile modulus was greater compared to the conductivity of the CPCs.
The effect of recycled silicone catheter (rSC) on tensile properties (tensile strength, modulus at 100% elongation and elongation at break) and morphology of recycled silicone catheter filled epoxidised natural rubber (ENR 50/rSC) vulcanizates were studied in loading range of 0 to 50 phr with two different size; fine (300-600μm) and coarse (1-2 cm). For tensile properties, tensile strength, modulus at 100% elongation (M100) and elongation at break (EB) for both ENR 50/rSC fine and coarse vulcanizates show increment up to 15 phr but then decreased as the rSC content increased. Comparison between ENR 50/rSC fine and coarse vulcanizates indicates that ENR 50/rSC fine vulcanizates has better tensile properties than ENR 50/rSC coarse vulcanizates due to better dispersion and filler-rubber interaction as proven in morphological study. The results indicate that the morphology of ENR 50/rSC fine vulcanizate is better than that of ENR 50/rSC coarse vulcanizates in which fine rSC well bonded with ENR 50.
The role of activated carbon (AC) in rubber compounds was investigated to better understand the reinforcing mechanism. The activated carbon filled styrene butadiene rubber vulcanizates (SBR-AC) using bamboo activated carbon as filler were prepared by using two-roll mill and cured at 160 °C. AC filler loading from 10 to 50 phr (part per hundred rubber) were used in this study. Study into the influences of filler loading on the cure characteristics, swelling behavior, physical properties (hardness and resilience), mechanical properties (tensile properties) and morphology of SBR-AC vulcanizates were carried out. It was observed that SBR-AC vulcanizates has better cure characteristics compared to the styrene butadiene rubber gum vulcanizate (SBR-GV) which is a non-filled vulcanizate. The results showed that the scorch time (ts2) decreased with increasing filler loading. The cure time (tc90) slightly decreased up to 20 phr before a rise as the filler loading increased. The minimum torque (ML) of SBR vulcanizate increased and the maximum torque (MH) decreased up to 20 phr but then increased with increasing filler loading. The cure rate index (CRI) of SBR-GV vulcanizate was higher than that of all SBR-AC vulcanizates. Up to 20 phr of filler loading, the CRI increased before a decline occurred as the filler loading increased. As expected, the hardness value of SBR-AC vulcanizates was higher compared to SBR-GV vulcanizate which has lower resilience. The hardness and crosslink density showed an increasing trend meanwhile the resilience was adversely affected by the increase in filler loading. The tensile properties of SBR-AC vulcanizates also showed improvement in which the tensile strength and modulus at 100% elongation (M100) increased with increasing filler content. It has been proved in morphology study of the tensile fracture surfaces. Bamboo activated carbon showed some potential enhancement on the reinforcing and physical properties as well as mechanical properties of the vulcanizates.
Tensile test and morphology studies were performed to determine the influences of Trans-polyoctylene Rubber (TOR) as compatibilizer of NBRr filled ENR 50 with composition of 15 phr. Fine size (300μm-700μm) of NBRr was used as fillers. Both uncompatibilized and compatibilized NBRr/ENR 50 were prepared using two roll mill at room temperature with different php of 1.0, 1.5, 2.0, 2.5 and 3.0. It can be observed that tensile strength and modulus of elasticity were decreased as increased in TOR loading before started to increased at 1.5 up to 3.0. Meanwhile, the increment in the value of elongation at break when increased in the addition of TOR. The scanning electron microscopy (SEM) of the tensile surface fracture of increased TOR loading illustrated a better adhesion and dispersion in comparison of low amount of TOR loading.
20 March 2025 in Archives of Metallurgy and Materials
The recent advancement in the flexible electronic devices have led to a growing interest around conductive polymer composites (CPCs). In this present study, a Linear Low-Density Polyethylene (LLDPE)/Carbon Black (CB) conductive polymer composites and Liquid Silicone Rubber (LSR)/CB conductive polymer composites were made by melt compounding and mixing technique, respectively. The CB serves as conductive filler enhances the performance of LLDPE and LSR by improving their electrical conductivity in the composite systems. In this study, various CB loadings (2 wt.%, 4 wt.%, 6 wt.%, 8 wt.%, and 10 wt.%) had been incorporated within LLDPE and LSR matrices respectively. The CPCs were melt blended using an internal mixer for LLDPE/CB composite, whereas, for LSR/CB composite, a stir mixing technique was employed. In general, additions of CB within LLDPE and LSR matrices had affected the tensile properties of the composites. Nevertheless, it was found that the electrical conductivity for both CPCs were increased with increasing of CB loading. The SEM micrographs revealed the morphology of a fractured CPCs samples. Formation of a network path was believed to be the primary reasons for the increased in electrical conductivity of both composites systems and it was anticipated that the percolation threshold for both CPCs was at 6 wt.% loading.