8 February 2018 in IEEE Transactions on Industrial Electronics
The phase-shifted full-bridge (PSFB) converter has been widely used in medium-to-high power applications because of simple topology and ease of achieving soft-switching for power switches. However, with the phase-shifted control, the electric potential variation of the two phase-leg midpoints happens at different times, and the displacement current generated by two midpoints through associated parasitic capacitance (including the parasitic capacitance between two midpoints to ground and the transformer inter-winding capacitance) cannot be cancelled by each other, resulting in a serious common mode (CM) noise. Moreover, the resonant inductor voltage affects the electric potentials of the transformer terminals, which also generates CM noise. To reduce the CM noise in the PSFB converter, this paper proposes a symmetrical resonant inductor together with symmetrical transformer configuration to eliminate the influence of the resonant inductor voltage on the CM noise. Then, a passive cancellation circuit is introduced to cancel the effect of the voltages between the midpoints and the ground on the CM noise. A 1-kW PSFB converter prototype has been fabricated and tested in the lab, and the experimental results are provided to verify the proposed methods.
1 May 2021 in IEEE Transactions on Industrial Electronics
Common-mode (CM) noise cancellation method is an attractive approach to reduce the original CM noise in power converters, which helps to shrink the size of electromagnetic interference (EMI) filter. Traditional CM noise cancellation method cancels the CM noise current by adding a branch consisted of a compensation voltage source and a compensation capacitor, which generates a cancellation current and nullifies the noise current. As the duality, the voltage cancellation method is also feasible for reducing CM noise, which has not been investigated in DC-DC converters. In this paper, a common-mode voltage cancellation (CMVC) method is proposed, which cancels the CM voltage of the converter by inserting compensation voltage source into the input power cord. The requirement for achieving CMVC is that the cancellation voltage and the parasitic capacitances in the circuit are matched. The applications of CMVC method in basic non-isolated and isolated dc-dc converters are presented, and the considerations for practical applications of this method are discussed. Finally, a buck converter and a half-bridge LLC resonant converter prototype are built, and the proposed method is verified by experiment, respectively.
11 February 2021 in IEEE Transactions on Power Electronics
It is well known that PWM inverters generate common-mode (CM) voltages, which may cause the CM electromagnetic interference and leakage current in the applications such as photovoltaic or motor drive systems. The CM noise issue becomes more severe with the application of silicon-carbide devices, which have higher dv/dt than silicon devices. In this article, a passive cancellation method is proposed by inserting two CM transformers (CMT) into the input and output side of the inverter, respectively. The selection of the turns ratio for two CMTs is analyzed and revealed to achieve the best CM noise cancellation, and the influence of the parasitics in the CMT is investigated as they limit the bandwidth for CM noise cancellation. Compared to the passive filter, floating filter, and the active cancellation method, the proposed method could reduce the CM noise at both sides simultaneously regardless of the CM impedance of the source or the load. A single-phase inverter is built, and the proposed method achieves 40 dB reduction at both sides, which verifies the effectiveness of the proposed method.
14 July 2020 in IEEE Transactions on Components, Packaging and Manufacturing Technology
To develop a thermal model for air-cooled plate-fin heatsink and evaluate its thermal performance, empirical equations are available to calculate the pressure drop and heat transfer coefficients for the fins rapidly. Besides the heat transfer coefficients, the local air temperature also affects the heat transfer of the fins, which rises along the channel by absorbing the released heat from fins. In this paper, a heatsink model to account for the air temperature rise is proposed, and a thermal circuit model is used to correlate the increased air temperature and the absorbed heat at the fin boundary. With this convective boundary, the temperature distribution for the base plate of the heatsink is calculated by adopting finite difference method (FDM), which analyzes conductive heat transfer for the base plate. Both of them have been programmed in MATLAB software, and the calculated temperature by the proposed models is compared with computational fluid dynamics (CFD) simulation. A fan cooled plate-fin heatsink for a half-bridge power electronics inverter is tested in the lab as an example, and the thermal results obtained from the proposed models are within 10% of error with respect to CFD simulation results and experimental results. The proposed method is also faster than CFD simulation. The proposed accurate and rapid thermal modelling method will be essential for virtual prototyping and layout/geometry optimization of power electronics systems.
5 June 2023 in IEEE Transactions on Industrial Electronics
This article proposes a quasi-three-level (Q3L) pulsewidth modulation (PWM)-based module-parallel inverter to address two major issues of deploying SiC mosfet s in high-power cable-fed adjustable speed drives. First, the maximum output power of SiC inverters is limited due to the lack of high current rating silicon carbide (SiC) devices, which cannot satisfy the demand of high-power applications, such as heavy-duty electric vehicles and more electric airplanes. The second issue comes from the fast-switching speed of SiC mosfet s, where power cables act like transmission lines under steep rising/falling voltages (high $dv/dt$ ), with back-and-forth voltage reflections that result in serious overvoltage oscillations at motor terminals. To address these issues, a SiC module-parallel inverter is adopted with elevated current capacity, where the phase voltage is maintained at the midpoint of a coupled inductor connected to the output nodes of each paralleled half-bridge module. By actively controlling the switching delay between the paralleled half-bridge legs, Q3L PWM waveforms are generated at the inverter output nodes that can mitigate the motor overvoltage due to the voltage reflections through power cables. An active current control technique is also proposed to facilitate the current balance between the paralleled half-bridge legs. The proposed Q3L PWM-based module-parallel inverter is experimentally verified using a SiC-based cable-fed motor drive system. The results show that the proposed approach can extend the current capabilities of SiC devices as well as mitigate motor overvoltage, enabling the adoption of SiC devices in high-power motor drives.
7 July 2021 in IEEE Transactions on Power Electronics
The common-mode (CM) noise in nonisolated dc-dc converters is mainly caused by the displacement current through the high dv/dt node in the circuit and the associated parasitic capacitance, and it may cause electromagnetic interference (EMI) to the surrounding equipments. To reduce the original CM noise and shrink the EMI filter size of non-isolated dc-dc converters, CM noise cancellation methods have been proposed, including the symmetry circuit, balancing technique, passive cancellation and CM voltage cancellation. In these methods, additional components or windings are required for reducing the CM noise. In this article, a new CM noise cancellation method in non-isolated dc–dc converters is proposed by adopting a split-winding configuration. Compared to the existing CM noise cancellation methods which require additional components, the proposed method in the buck, boost and single-ended primary-inductor converter (SEPIC) converters which runs in voltage step-up mode has the identical volume as their conventional circuit configurations. The proposed method is verified for a buck converter by experiment.