A sub-THz (88–136 GHz) full-duplex (FD) phased-array transceiver (TRX) integrating an RF self-interference (SI) canceller with differential feeding FD antennas is presented in this work. The LO phase generation chain controls differential transmitter outputs for the phased-array operation. The differential feeding FD antenna with differential pairs of chips achieves over 35-dB SI suppression. The SI suppression is improved by 20 dB when the SI canceller is turned on. Without any digital-domain SI cancellation (SIC), a total SI suppression of $>$ 60 dB is achieved over a 2-GHz bandwidth. The proposed neutralized mixer with over 20-dB LO feedthrough suppression and wideband RF amplifiers support a large data rate at sub-THz frequencies. This is the world’s first demonstrated sub-THz FD phased-array TRX. In the over-the-air (OTA) measurements for FD mode, the proposed FD TRX achieves 6 Gb/s in 8PSK and 4 Gb/s in 16QAM. It also achieves a 112-Gb/s data rate for OTA TX-to-RX.
Lightweight and deployable phased arrays are important in Small-Satellite (Small-Sat) constellation systems to reduce price and increase link distance. This article proposes a Ka-band deployable active phased-array TX on a 4-layer liquid crystal polymer (LCP) board for a lightweight and high stowage rate solution to break through the trade-off between high antenna aperture size and small form factor in phased arrays. This article describes detailed designs of the phased array and its building blocks with the proposed 4-layer LCP substrate structure. Assembled with the beamformer ICs (BFIC), a Ka-band 8×4-element deployable active phased-array TX on the 4-layer LCP substrate is fabricated. The proposed deployable phased-array TX can steer the beam from -50° to 50°. The phased-array TX can drive 32-APSK DVB-S2 signal with a -28.7 dB EVM as well, revealing that the deployable phased-array TX performs with high phased-array performance. Furthermore, the TX achieved the lightest and thinnest phased array with 0.96 kg/m 2 areal mass and 0.9 mm thickness. This groundbreaking research sets the stage for the realization of affordable and user-centric satellite communication (SATCOM) in low-earth orbit (LEO).
1 January 2026 in IEEE Journal of Solid-State Circuits
This paper introduces a testbed for joint radar-communication (JRC) utilizing frequency-division multiplexing (FDM) in the D-band (116–170 GHz). It employs a wideband 65 nm CMOS transceiver, originally designed for high-throughput communications. Utilizing external frequency-modulated continuous-wave (FMCW) chirps, it achieves a range resolution of 13.6mm and sub-millimeter accuracy in radar-only mode. In simultaneous JRC operation, it sustains a 24mm range resolution while supporting data rates up to 20 Gb/s using 16-QAM and 32-QAM modulation schemes. A single-transmitter, single-receiver (1T1R) configuration is used to demonstrate radar and communication coexistence within a shared spectrum, whereas an extended single-transmitter, two-receiver (1T2R) setup validates the simultaneous demodulation of both direct and reflected links, demonstrating multi-user capabilities. Doppler measurements are used to verify low-speed velocity sensing via segmented acquisition, illustrating how factors such as distance, radar cross section (RCS), and beam alignment together impact signal-to-noise ratio (SNR), radar visibility, and the quality of the communication link. This system-level validation marks the first experimental proof of a communication-focused architecture in the D-band, establishing the feasibility of scaling existing CMOS hardware for future integrated system-on-chip (SoC) solutions capable of simultaneous high-speed communication and fine-resolution sensing.
This letter presents the validation of a low-permittivity (εr = 1.88) PCB substrate for compact, 28-GHz phased-array antennas. A grounded-coplanar-waveguide(CPWG) feed and a three-layer stack-upwere verified using a TRL calibration board, confirming stable performance up to 60 GHz. A single via-fed patch antenna on the new laminate achieved 7.1 dBi gain, 3.2 dB higher than that on Megtron6 (εr = 3.7). A 1 × 4 array was implemented on the same stack-up achieved 9.2 dBi broadside gain and up to 0.8 dB lower scan loss at 60° compared with Megtron6. These results demonstrate the importance of substrate selection and highlight the potential of this laminate for PCB-based millimeter-wave antennas.
3 February 2026 in IEEE Journal of Solid-State Circuits
This article presents a 300-GHz-band amplifier-last outphasing phased-array transmitter with path mismatch calibration in a 65-nm CMOS technology. Calibration is essential for mitigating impairments in outphasing systems used for wideband communication. The transmitter integrates two independent sub-THz LO generation chains to calibrate the phase mismatch between two paths and configure the phase delay between different phased-array elements. An integrated RF outphasing amplifier calibrates the amplitude mismatch and improves the transmitter’s effective isotropic radiated power (EIRP). After calibration, the transmitter exhibits a 3.3-dB improvement in error vector magnitude and supports 16 QAM modulation at 52 Gb/s over a distance of 9 cm. It achieves a peak EIRP of 8.9 dBm at 246 GHz, with a minimum EIRP of 5.0 dBm across the frequency range from 237 to 250 GHz. An 8×1 phased-array transmitter is implemented, demonstrating a main lobe scanning range of ±12° in the $E$ -plane.