2 November 2021 in IEEE Journal of Solid-State Circuits
Highly stable on-chip frequency references offer the possibility of replacing crystal oscillators in many cost-and form-factor-constrained applications. However, achieving good frequency stability in a power-efficient manner across process, voltage, and temperature variations possess many design challenges. This article describes these challenges and presents a method for improving the integrated RC oscillator’s frequency accuracy by overcoming them. We show that the impact of resistor temperature coefficient (TC) on the accuracy of output frequency can be mitigated by using a parallel combination of two switched resistors that are digitally controlled by pulse-density modulated sequences. By trimming at only two temperatures, a prototype frequency-locked loop (FLL)-based 32-MHz oscillator fabricated in a 65-nm CMOS process achieves an inaccuracy of 530 ppm (8.4 ppm/°C), 80-ppm/V voltage sensitivity, 2.5-ppm Allan deviation, and 1- $\mu \text{W}$ /MHz power efficiency.
3 December 2018 in IEEE Transactions on Circuits and Systems II: Express Briefs
A low power RC relaxation oscillator with very low voltage and temperature sensitivities is presented. Supply sensitivity is reduced by using a self-regulation loop that biases the oscillator near its zero-voltage coefficient point. Fabricated in a 65-nm CMOS process, the prototype 1.5-MHz oscillator consumes 6 μW from 1-V supply and achieves better than ±50 ppm〉°C and ±1500 ppm/V temperature and voltage sensitivities, respectively.
27 January 2022 in IEEE Journal of Solid-State Circuits
A ring-oscillator (RO)-based low-jitter digital fractional-N frequency synthesizer is presented. It employs a frequency doubler (FD) that doubles the reference clock frequency, a 2-bit time-to-digital converter (TDC) with optimized thresholds to minimize the quantization error, and a high-resolution digital-to-time converter (DTC) to cancel the quantization error of the delta-sigma fractional divider (FDIV). DTC’s linearity is improved using a piecewise linear (PWL) function-based correction scheme. On-chip digital calibration is extensively used to correct imperfections of the FD, TDC, and DTC. A prototype synthesizer incorporating the proposed techniques and implemented in a 65-nm CMOS produces a 3.2-GHz output clock from a 96-MHz input clock. The worst-case integrated jitter is 306 and 405 fs in integer and fractional-N modes, respectively. The synthesizer consumes 11.7 mW from a 1-V supply of which 7.84 mW is consumed by the oscillator. The jitter figure-of-merit of the synthesizer is −237.2 dB.
27 May 2019 in IEEE Journal of Solid-State Circuits
Ultra-low-power systems, such as wearables and Internet-of-Things (IoT), require power- and volume-efficient micro-controller units (MCUs) capable of operating across a wide range of frequencies under extreme power constraints. This paper presents the techniques to implement clock generators that cater to the needs of such MCUs and other similar ultra-low-power applications. RC relaxation oscillators (RCOs) are shown to achieve excellent frequency stability when generating clocks in kilohertz to megahertz range but are not very power efficient (5 μW/MHz). Their power efficiency further degrades at higher frequencies because of additional power needed to compensate for the impact of temperature-dependent comparator's delay on frequency stability. On the other hand, ring oscillators (ROs) can generate higher frequency and lower noise clocks more power efficiently but exhibit very poor voltage and temperature sensitivity. In view of these complementary tradeoffs offered by RC oscillator and RO, this paper seeks to combine their advantages by using a phase-locked loop (PLL) to multiply the frequency of an RC oscillator using an RO. A new type-II digital PLL (DPLL) that uses a delay-modulating clock buffer to implement the proportional control and a low-area digital-to-analog converter to implement the digitally controlled oscillator is presented. Fabricated in the 65 nm CMOS process, the prototype PLL generates 50-300 MHz output frequencies from a reference clock in the range of 0.5-5 MHz. The DPLL occupies an active area of 125 μm x 125 μm and achieves ±0.33% period jitter while consuming 63.5 μW at an output frequency of 240 MHz. This translates to an excellent power efficiency of 0.26 μW/MHz at 0.8-V supply voltage.