This article presents frequency-modulated-continuous-wave (FMCW) radars developed for the detection of vital signs and gestures using two generations of 145-GHz transceivers (TRXs) integrated in 28-nm bulk CMOS. The performance and limitations of high-frequency radars are quantified with a system-level study, and the design and performance of individual circuit blocks are presented in detail. A 145-GHz center frequency and radar operation over an RF bandwidth of 10 GHz yield a displacement responsivity of 2 π rad/mm and a windowed range resolution of 30 mm, respectively. Radar operation over a 0.1-7 m range is enabled by an effective-isotropic radiated power of 11.5 dBm and a noise figure of 8 dB. The ICs feature frequency multiplication by 9 in the transmit and receive paths, sub-arrayed dipole antennas, and neutralization of TX-RX leakage via delay control. A single TRX dissipates 500 mW from a 0.9-/1.8-V drive. The use of fast chirps (5-30- μs) mitigates the effect of 1/ f-noise at the intermediate frequency (IF). Extensive characterization results showcase state-of-the-art performance of the TRXs, while the code-domain multiple-input and multiple-output (MIMO) radars ( 1 ×4 and 4 ×4) built with them demonstrate vital-sign and gesture detections.
21 March 2022 in IEEE Journal of Solid-State Circuits
This article presents a 135–155-GHz low-power and high-efficiency frequency multiply-by-9 (x9) frequency-modulated continuous-wave (FMCW) radar transmitter (TX). Starting from a 16-GHz frequency-chirping input signal, cascaded frequency triplers at $V$ -band (40–75 GHz) and $D$ -band (110–170 GHz) bring the signal to the $D$ -band, subsequently amplified and radiated via a power amplifier (PA) and an on-chip antenna at $D$ -band. The $D$ -band PA with a reduced gain of transistors at $f_{\max }$ /2 proposes a broadband gain-boosting technique, achieving a maximum achievable gain ( $G_{\max }$ ) for broad frequency range with high-order embedding passives. The x9 chain proposes phase-controlled frequency triplers that align the phase of each harmonic contribution and boost the third harmonic output power, conversion gain, and dc-to-RF efficiency. Implemented in a 28-nm CMOS process, the TX achieves a measured effective isotropic radiated power (EIRP) of 9.4 dBm, a dc-EIRP efficiency of 16.6% while exhibiting an antenna gain de-embedded output power of 7.1 dBm, and a dc-to-RF efficiency of 9.7% with less than 77-mW dc power consumption.
Connecting chips within a module is a basic requirement in transforming MMIC performance to system functionality. More and more applications demand for operation at high mm-wave frequencies or with ultra-large bandwidth. While semiconductor devices have seen tremendous progress in terms of their frequency limits, the chip interconnects lag behind and often form the bottleneck in realizing such systems. This paper reviews the broadband potential of the most common interconnect types in use and their performance demonstrated so far, covering wirebonding, approaches with chips embedded in a substrate, and flip-chip. Additionally, as an intermediate solution between system-on-chip and system-in-a-package, semiconductor hetero-integration on the chip-level is included. As is discussed, bond wire interconnects are most limited in bandwidth among the four types and reach the 100 GHz band only at the expense of narrowband characteristics. Dedicated embedded-chip packaging techniques show significantly better performance, bandwidths in the order of 100 GHz have been shown in the literature. Flip-chip has clearly the highest potential, interconnects covering the range from DC to 500 GHz have been demonstrated and are presented in the paper. Hetero-integration on the chip proves to allow for very broadband interconnects between elements and circuits on the compound chip as well: For an InP-on-BiCMOS process 325 GHz bandwidth were achieved and even higher values seem to be feasible.
21 October 2020 in IEEE Transactions on Antennas and Propagation
This paper presents the design of integrated antennas in the D-Band (110-170 GHz). First, an electromagnetic analysis is used to tune the propagation characteristics of surface waves supported on an artificial magnetic conductor (AMC). Next, a sub-array of two miniaturized dipoles is designed where each dipole attains axial resonance and the separation between them is optimized for substrate wave cancellation. This sub-array simultaneously performs spatial power combining and substrate wave cancellation, leading to significant increase of the effective isotropic radiated power (EIRP). Two miniaturized dipoles with axial length of 252 μm and spacing of 450 μm was fabricated in 28 nm bulk CMOS with low resistivity silicon (10 Ω-cm). Each dipole is fed by a cascade of two triplers and a power amplifier. Measurements show a gain of 2.3 dBi, EIRP of 12.2 dBm at 139 GHz and a 3 dB bandwidth of 127-154 GHz (19% fractional) without using any additional substrates, lenses or post-processing steps. Scalability of this technique for forming larger arrays is also presented.
13 May 2015 in IEEE Microwave and Wireless Components Letters
With the increasing availability of MMICs at frequencies beyond 100 GHz low-loss interconnects for module fabrication in this frequency range become essential. This letter presents results on a flip-chip mounting approach exhibiting a bandwidth of more than 250 GHz, supporting both coplanar and stripline transitions. The interconnects are realized with 10 μm-diameter AuSn microbumps. S-parameter measurements show an insertion loss of less than 1.0 dB per interconnect and a return loss better than 10 dB up to 250 GHz. The experimental results are in good agreement with 3-D EM simulations.
15 April 2022 in IEEE Journal of Solid-State Circuits
A 139.5–157.7-GHz $D$ -band I/Q radar receiver with an on-chip antenna and a spillover resilient $N$ -path baseband filter is presented. Spillover and its manifestation based on the chirp duration are discussed, and a filter for spillover mitigation is implemented. The radar is characterized by 18-GHz radio frequency (RF) bandwidth, 13-mm range resolution, 55-dB conversion gain, 8-dB NF, and 26-dB narrowband spillover attenuation. The receiver is also capable of selectively mitigating close-by large reflectors, and the system power consumption is 67 mW.