6 January 2021 in IEEE Transactions on Industrial Electronics
The complexity of winding distribution of doubly salient electro-magnetic machine (DSEM) results in its uneven temperature distribution, and its temperature rise characteristics under different working conditions need to be further studied. Different from the thermal analysis method of uniformly distributed electrical machine, this article proposes a time-saving thermal analysis method for the new topology of DSEM. In view of the sensitive change of DSEM excitation loss with temperature, the magnetic-thermal bidirectional coupling method is adopted. Considering the temperature difference between excitation and armature coils, a detailed thermal model is established for the armature-excitation slot. The number of bidirectional coupling iterations of finite-element method is reduced by steady-state temperature prediction. Then the temperature distribution of DSEM is analyzed in detail, and the variation of the temperature distribution under different operating conditions is studied. The temperature rise characteristics of a three-phase 12/8-pole prototype are tested to verify the correctness of the proposed method. The research results can provide reference for the temperature evaluation of DSEM and its electromagnetic and cooling design.
14 June 2019 in IEEE Transactions on Industrial Electronics
Owing to the merits of smaller voltage ripples, lower armature current and cost compared to full-control (FC), the angular position semi-control (APSC) scheme is proposed in this paper for low speed range of the doubly salient electro-magnetic generator (DSEG) operating over wide speed range, which improve the output voltage without increasing the field current. In APSC, the energy is stored with positive current in the inductance rising area and negative current in the inductance falling area, by which the output power and voltage increase, and the excitation current reduces. Moreover, in order to improve the poor dynamic performance resulting from the large storage capacitor required for APSC, an ideal output voltage model is established according to the ampere-second balance of the energy storage capacitor on the load side firstly. Secondly, several correction methods are investigated to enhance the accuracy of the ideal model. Finally, based on the conduction angle estimation model, a novel output voltage control strategy is put forward. The feasibility and superior dynamic performance of the proposed strategy are validated by the experiment results.
8 June 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Torque ripples caused by the particular doubly salient structure of the doubly salient electromagnetic machine (DSEM) restrict its application in the field requiring high performance. This paper employs the current given function (CGF) to propose a torque ripple reduction strategy for DSEM to enhance the torque capability. The optimal current profile for minimizing the copper loss is obtained based on the theoretical analysis. It is found that the obtained three-phase currents are distributed according to the phase torque coefficient that represents the torque capability of each phase. Then, to minimize the torque ripple and copper loss, four CGFs are proposed to distribute the reference current of each phase according to the torque characteristics of DSEM. Finally, the influence of overlap angle on the proposed strategy is analyzed to select the reasonable CGF and overlap angle under different operating conditions through simulation, improving the current tracking performance and torque-ampere ratio. The simulation and experimental results demonstrate the effectiveness of the proposed strategy in suppressing torque ripple and improving the torque-ampere ratio.
28 April 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
21 September 2021 in IEEE Transactions on Power Electronics
The controlled rectification method with positon sensor can effectively improve the output power of the doubly salient electromagnetic generator (DSEG), but weakens the advantage of no position sensor for the traditional DSEG with uncontrolled rectification. To solve this problem, a current self-injection based position sensorless control method is proposed for DSEG with H-bridge semi-controlled rectifier (HBSCR) in this article. Based on the operation principle of DSEG and HBSCR, the position estimation method is developed from the positive zero-crossing point of inductive electromotive force (EMF), which is indirectly observed through the test current self-injected by the inductive EMF. According to the relationship between generation current and test current, a test current self-injection method without presetting injection width is put forward, and the corresponding sensorless control strategy is established with the combination of angular position semi-control. Then, the compensation strategy is further presented to improve the accuracy of the proposed position estimation method. Finally, the simulations and experiments are implemented on a three-phase DSEG to validate the feasibility and correctness of the proposed sensorless control strategy.
25 May 2021 in IEEE Transactions on Industrial Electronics
The dynamic response of conventional doubly salient electro-magnetic generator (DSEG) system with uncontrolled rectification is slow, owing to its large time constant resulting from the large energy storage capacitance and field winding inductance. In this article, the minimum field current increment control strategy is proposed for the DSEG system with angular position control (APC) rectification to solve this problem. Based on the ampere-second balance of the energy storage capacitor on the load side, the output voltage estimation model of APC is established to analyze the working characteristics of APC under different conditions in detail. Then, the method to minimize the field current increment by controlling the conduction angle is put forward to improve the dynamic response, because the smaller variation corresponds to the better dynamic performance. Finally, the experiments on a 12/8 pole DSEG system with controlled rectification are implemented to validate the effectiveness of the proposed control strategy, and the improved dynamic performance is observed in the results.