1 March 2016 in Archives of Foundry Engineering
Paper presents the results of studies on primary crystallization and wear resistance of high chromium cast iron inoculated with ferrotitanium intended for work in abrasive conditions. Primary crystallization was examined with use of TDA method, wear tests of the samples were conducted using the modified pin-on-disk method.
23 April 2014 in Journal of Materials Engineering and Performance
This paper presents the effect of carburizing materials on cast iron solidification and crystallization. The studies consisted of cast iron preparation from steel scrap and different carburizers. For a comparison, pig iron was exclusively used in a solid charge. Crystallization analysis revealed the influence of the carburizer material on the crystallization curves as well as differences in the solidification paths of cast iron prepared with the use of different charge materials. The carburizers’ influence on undercooling during the eutectic crystallization process was analyzed. The lowest undercooling rate was recorded for the melt with pig iron, then for synthetic graphite, natural graphite, anthracite, and petroleum coke (the highest undercooling rate). So a hypothesis was formulated that eutectic cells are created most effectively with the presence of carbon from pig iron (the highest nucleation potential), and then for the graphite materials (crystallographic similarity with the carbon precipitation in the cast iron). The most difficult eutectic crystallization is for anthracite and petroleum coke (higher undercooling is necessary). This knowledge can be crucial when the foundry plant is going to change the solid charge composition replacing the pig iron by steel scrap and the recarburization process.
1 June 2017 in Archives of Metallurgy and Materials
Metal matrix composite (MMC) surface layers reinforced by WC were fabricated on armor steel ARMOX 500T plates via a laser surface alloying process. The microstructure of the layers was assessed by scanning electron microscopy and X-ray diffraction.The surface layers having the WC fraction up to 71 vol% and an average hardness of 1300 HV were produced. The thickness of these layers was up to 650 μm. The addition of a titanium powder in the molten pool increased the wettability of WC particles by the liquid metal in the molten pool increasing the WC fraction. Additionally, the presence of titanium resulted in the precipitation of the (Ti,W)C phase, which significantly reduced the fraction of W-rich complex carbides and improved a structural integrity of the layers.
1 June 2015 in Archives of Foundry Engineering
Details var a2a_config = a2a_config || {}; a2a_config.onclick = 1; a2a_config.locale = "pl"; a2a_config.color_main = "D7E5ED"; a2a_config.color_border = "9D9D9D"; a2a_config.color_link_text = "ffffff"; a2a_config.color_link_text_hover = "ffffff"; a2a_config.color_bg = "d9d9d9"; a2a_config.icon_color = "#4e4e4e"; a2a_config.exclude_services = ["dihitt", "delicious", "whatsapp", "dzone", "sms", "stumpedia", "viber", "yahoo_messenger", "google_plus"]; Details PDF BIBTEX RIS Title Stereological Analysis of Carbides in Hypoeutectic Chromium Cast Iron Journal title Archives of Foundry Engineering Yearbook 2015 Issue No 2 Authors Gromczyk, M. ; Studnicki, A. ; Kondracki, M. ; Szajnar, J. Keywords stereological parameters ; Fe-C-Cr alloys ; Chromium carbide ; Chromium cast iron Divisions of PAS Nauki Techniczne Publisher The Katowice Branch of the Polish Academy of Sciences Date 2015[2015.01.01 AD - 2015.12.31 AD] Type Artykuły / Articles Identifier DOI: 10.1515/afe-2015-0030 Source Archives of Foundry Engineering; 2015; No 2 References Studnicki (2004), Experimental modelling of casting cooling in the mould, Archives.
1 May 2005 in Journal of Materials Processing Technology
1 March 2015 in Archives of Foundry Engineering
In the paper the results and analysis of abrasive wear studies were shown for two grades of cast steels: low-alloyed cast steel applied for heavy machinery parts such as housing, covers etc. and chromium cast steels applied for kinetic nodes of pin-sleeve type. Studies were performed using the modified in Department of Foundry pin-on-disc method