Jack Kramer

Jack Kramer

Auto-generated profile, based on publicly available information

Jack Kramer

The University of Texas at Austin

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 October 2023 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
OBOmar Barrera
Omar Barrera
SCSinwoo Cho
Sinwoo Cho
LMLezli Matto
Lezli Matto
JKJack Kramer
Jack Kramer
KHKenny Huynh
Kenny Huynh
RLRuochen Lu
Ruochen Lu
This work reports an acoustic filter at 23.5 GHz with a low insertion loss (IL) of 2.38 dB and a 3-dB fractional bandwidth (FBW) of 18.2%, significantly surpassing the state-of-the-art. The device leverages electrically coupled acoustic resonators in 100 nm 128 $^{\circ}$ Y-cut lithium niobate (LiNbO $_{3})$ piezoelectric thin film, operating in the first-order antisymmetric (A1) mode. A new film stack, namely transferred thin-film LiNbO $_{3}$ on silicon (Si) substrate with an intermediate amorphous silicon (a-Si) layer, facilitates the record-breaking performance at millimeter-wave (mmWave). The filter features a compact footprint of 0.56 mm $^{2}$ . In this letter, acoustic and EM consideration, along with material characterization with X-ray diffraction and verified with cross-sectional electron microscopy are reported. Upon further development, the reported filter platform can enable various front-end signal-processing functions at mmWave.2023-0129

20 October 2023 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
SCSinwoo Cho
Sinwoo Cho
OBOmar Barrera
Omar Barrera
PSPietro Simeoni
Pietro Simeoni
EMEmily N. Marshall
Emily N. Marshall
JKJack Kramer
Jack Kramer
RLRuochen Lu
Ruochen Lu
This work reports a millimeter wave (mmWave) thin-film bulk acoustic resonator (FBAR) in sputtered scandium aluminum nitride (ScAlN). This paper identifies challenges of frequency scaling sputtered ScAlN into mmWave and proposes a stack and new fabrication procedure with a sputtered Sc $_{\mathbf{0.3}}$ Al $_{\mathbf{0.7}}$ N on Al on Si carrier wafer. The resonator achieves electromechanical coupling ( k $^{\mathbf{2}}$ ) of 7.0% and quality factor ( Q) of 62 for the first-order symmetric (S1) mode at 21.4 GHz, along with k $^{\mathbf{2}}$ of 4.0% and Q of 19 for the third-order symmetric (S3) mode at 55.4 GHz, showing higher figures of merit (FoM, k $^{\mathbf{2}}$ $\cdot$ Q) than reported AlN/ScAlN-based mmWave acoustic resonators. The ScAlN quality is identified by transmission electron microscopy (TEM) and X-ray diffraction (XRD), identifying the bottlenecks in the existing piezoelectric-metal stack. Further improvement of ScAlN/AlN-based mmWave acoustic resonators calls for better crystalline quality from improved thin-film deposition methods. 2023-0151

15 October 2024 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
OBOmar Barrera
Omar Barrera
NRNishanth Ravi
Nishanth Ravi
KSKapil Saha
Kapil Saha
SDSupratik Dasgupta
Supratik Dasgupta
JCJoshua Campbell
Joshua Campbell
RLRuochen Lu
Ruochen Lu
This work reports an acoustic solidly mounted resonator (SMR) at 18.64 GHz, among the highest operating frequencies reported. The device is built in scandium aluminum nitride (ScAlN) on top of silicon dioxide (SiO $_{2})$ and tantalum pentoxide (Ta $_{2}$ O $_{5})$ Bragg reflectors on silicon (Si) wafer. The stack is analyzed with X-ray reflectivity (XRR) and high-resolution X-ray diffraction (HRXRD). The resonator shows a coupling coefficient ( $k^{2})$ of 2.0%, high series quality factor ( $Q_{s})$ of 156, shunt quality factor ( $Q_p)$ of 142, and maximum Bode quality factor ( $Q_{max})$ of 210. The third-order harmonics at 59.64 GHz is also observed with $k^{2}$ around 0.6% and $Q$ around 40. Upon further development, the reported acoustic resonator platform can enable various front-end signal-processing functions, e.g., filters and oscillators, at future frequency range 3 (FR3) bands.2024-0120

15 July 2024 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
THTzu-Hsuan Hsu
Tzu-Hsuan Hsu
JCJoshua Campbell
Joshua Campbell
JKJack Kramer
Jack Kramer
SCSinwoo Cho
Sinwoo Cho
MLMing-Huang Li
Ming-Huang Li
RLRuochen Lu
Ruochen Lu
In this work, we demonstrate a C-band shear-horizontal surface acoustic wave (SH-SAW) resonator with high electromechanical coupling ( ${k}_{\mathbf{t}}^{\mathbf{2}})$ of 22% and a quality factor ( $Q)$ of 565 based on a thin-film lithium niobate (LN) on silicon carbide (SiC) platform, featuring an excellent figure-of-merit (FoM $=$ ${k}_{\mathbf{t}}^{\mathbf{2}}\cdot Q_{{max}})$ of 124 at 6.5 GHz, the highest FoM reported in this frequency range. The resonator frequency upscaling is achieved through wavelength ( $\lambda )$ reduction and the use of thin aluminum (Al) electrodes. The LN/SiC waveguide and synchronous resonator design collectively enable effective acoustic energy confinement for a high FoM, even when the normalized thickness of LN approaches a scale of 0.5 $\lambda $ to 1 $\lambda $ . To perform a comprehensive study, we also designed and fabricated five additional resonators, expanding the $\lambda $ studied ranging from 480 to 800 nm, in the same 500 nm-thick transferred Y-cut thin-film LN on SiC. The fabricated SH-SAW resonators, operating from 5 to 8 GHz, experimentally demonstrate a ${k}_{\mathbf{t}}^{\mathbf{2}}$ from 20.3% to 22.9% and a $Q$ from 350 to 575, thereby covering the entire C-band with excellent performance.2024-0070

7 July 2025 in Applied Physics Letters
Verified
Journal Article
Closed access
JKJack Kramer
Jack Kramer
BBBryan T. Bosworth
Bryan T. Bosworth
LMLezli Matto
Lezli Matto
NJNicholas R. Jungwirth
Nicholas R. Jungwirth
OBOmar Barrera
Omar Barrera
RLRuochen Lu
Ruochen Lu
Piezoelectric resonators are a common building block for signal processing because of their miniature size, low insertion loss, and high quality factor. As consumer electronics push to millimeter wave frequencies, designers must increase the operating frequency of the resonator. The current state-of-the-art approach to increase the operating frequency is to decrease the thickness of the piezoelectric film to shorten the acoustic wavelength or to use higher order modes. Unfortunately, maintaining high quality factors typically requires thicker piezoelectric layers. Thinner individual layers suffer from higher defect densities and increased relative losses from surface related damping, which degrade the electromechanical coupling and quality factor. While acoustic high order modes can also increase operating frequency, the electromechanical coupling rapidly decreases with increasing mode number. Here, we overcome these limitations by utilizing a piezoelectric stack of three layers of lithium niobate with alternating crystallographic orientations to preferentially support higher order modes and thereby enhance the electromechanical coupling without degrading the quality factor. Our approach improves the figure of merit of millimeter wave acoustic resonators by roughly an order of magnitude greater compared to state-of-the-art piezoelectric resonators above 60 GHz. This concept of alternating crystallographic orientations facilitates a path to develop millimeter wave resonators with high figures of merit, low insertion loss, and miniature footprints, enabling applications in millimeter wave signal processing and computing.

2 March 2023 in Nature Communications
Verified
Journal Article
Open access
PDF file
DLDaehun Lee
Daehun Lee
SJShahin Jahanbani
Shahin Jahanbani
JKJack Kramer
Jack Kramer
RLRuochen Lu
Ruochen Lu
KLKeji Lai
Keji Lai
Implementing microelectromechanical system (MEMS) resonators calls for detailed microscopic understanding of the devices, such as energy dissipation channels, spurious modes, and imperfections from microfabrication. Here, we report the nanoscale imaging of a freestanding super-high-frequency (3 – 30 GHz) lateral overtone bulk acoustic resonator with unprecedented spatial resolution and displacement sensitivity. Using transmission-mode microwave impedance microscopy, we have visualized mode profiles of individual overtones and analyzed higher-order transverse spurious modes and anchor loss. The integrated TMIM signals are in good agreement with the stored mechanical energy in the resonator. Quantitative analysis with finite-element modeling shows that the noise floor is equivalent to an in-plane displacement of 10 fm/√Hz at room temperatures, which can be further improved under cryogenic environments. Our work contributes to the design and characterization of MEMS resonators with better performance for telecommunication, sensing, and quantum information science applications.