20 October 2023 in Journal of Microelectromechanical Systems
This work reports an acoustic filter at 23.5 GHz with a low insertion loss (IL) of 2.38 dB and a 3-dB fractional bandwidth (FBW) of 18.2%, significantly surpassing the state-of-the-art. The device leverages electrically coupled acoustic resonators in 100 nm 128 $^{\circ}$ Y-cut lithium niobate (LiNbO $_{3})$ piezoelectric thin film, operating in the first-order antisymmetric (A1) mode. A new film stack, namely transferred thin-film LiNbO $_{3}$ on silicon (Si) substrate with an intermediate amorphous silicon (a-Si) layer, facilitates the record-breaking performance at millimeter-wave (mmWave). The filter features a compact footprint of 0.56 mm $^{2}$ . In this letter, acoustic and EM consideration, along with material characterization with X-ray diffraction and verified with cross-sectional electron microscopy are reported. Upon further development, the reported filter platform can enable various front-end signal-processing functions at mmWave.2023-0129
1 January 2023 in Journal of Vacuum Science & Technology A
Smooth (< 0.5 nm rms) and subsurface damage-free (010) β-Ga2O3 was achieved with low-pressure chemical mechanical polishing. An applied pressure of 1 kPa along with colloidal silica and poromeric polyurethane polishing pads rotating at 30 rpm was found to be the optimal polishing parameters for (010) β-Ga2O3. Using higher pressures typically employed in the current literature induced subsurface damage in the substrates. Diffuse scatter intensity of triple-axis x-ray rocking curves was used to determine the presence of subsurface lattice damage, which was quantified by measuring peak widths below the half maximum (i.e., FWXM where X < 0.5). The initially rough surfaces of (010) β-Ga2O3 substrates due to wafer slicing and grinding were lapped and polished. A 5 μm Al2O3 slurry followed by a 0.3 μm Al2O3 slurry was used as the primary lap material removal step. The material removal rates were ∼20 and ∼9 μm/h, respectively. Then, chemical mechanical polishing was performed using colloidal alumina followed by colloidal silica. The removal rates were ∼1.3 and ∼0.4 μm/h, respectively. Only colloidal silica showed the complete removal of subsurface damage. The final (020) β-Ga2O3 rocking curve FWHM was ∼13″ and FW(0.001)M was ∼120″, which matches the widths of commercially available pristine (010) β-Ga2O3. A final cleaning step using dilute bleach and dilute citric acid to remove residual silica slurry particles from the surface was demonstrated.
7 July 2025 in Applied Physics Letters
Piezoelectric resonators are a common building block for signal processing because of their miniature size, low insertion loss, and high quality factor. As consumer electronics push to millimeter wave frequencies, designers must increase the operating frequency of the resonator. The current state-of-the-art approach to increase the operating frequency is to decrease the thickness of the piezoelectric film to shorten the acoustic wavelength or to use higher order modes. Unfortunately, maintaining high quality factors typically requires thicker piezoelectric layers. Thinner individual layers suffer from higher defect densities and increased relative losses from surface related damping, which degrade the electromechanical coupling and quality factor. While acoustic high order modes can also increase operating frequency, the electromechanical coupling rapidly decreases with increasing mode number. Here, we overcome these limitations by utilizing a piezoelectric stack of three layers of lithium niobate with alternating crystallographic orientations to preferentially support higher order modes and thereby enhance the electromechanical coupling without degrading the quality factor. Our approach improves the figure of merit of millimeter wave acoustic resonators by roughly an order of magnitude greater compared to state-of-the-art piezoelectric resonators above 60 GHz. This concept of alternating crystallographic orientations facilitates a path to develop millimeter wave resonators with high figures of merit, low insertion loss, and miniature footprints, enabling applications in millimeter wave signal processing and computing.
30 December 2024 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
This paper reports a surface acoustic wave (SAW) resonator at 52 GHz with a high quality factor ( Q ) of 188 and a high phase velocity of 12.2 km/s, marking the first millimeter wave (mmWave) SAW devices with high Q . Transferred 300 nm 128Y lithium niobate (LN) thin film on 4H silicon carbide (SiC) substrate is used for the acoustic platform. The dramatic frequency scaling is enabled by the high phase velocity thickness-shear mode, confined in the LN-SiC stack, thanks to the high stiffness and acoustic velocity of SiC. The high phase velocity of 12.2 km/s is approaching the longitudinal wave velocity of 12.5 km/s in 4H SiC. The resonator achieves electromechanical coupling ( k 2 ) of 0.5%, 3-dB series resonance Q ( Qs ) of 12, 3-dB shunt resonance Q ( Qp ) of 188, and maximum Bode Q of 154. Upon further development, the mmWave solidly mounted acoustic platform could enable various applications in signal processing, optomechanical, and quantum applications.
25 March 2025 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
This paper reports the first groups of low-loss acoustic solidly mounted resonators (SMR) and acoustic delay lines (ADL) at 14-20 GHz. Bulk acoustic waves (BAW) are confined in thin-film scandium aluminum nitride (ScAlN) on top of dielectric acoustic Bragg reflectors, consisting of alternating silicon dioxide with tantalum pentoxide (Ta2O5/SiO2) or niobium pentoxide (Nb2O5/SiO2) on Si carrier wafers. Stack material parameters are extracted via high-resolution X-ray diffraction (HRXRD) and X-ray reflectivity (XRR). The simulation and experiment show confinement for longitudinal BAW from 14-20 GHz. ADLs show high propagation Q above 478 and 171 for Ta2O5/SiO2 and Nb2O5/SiO2, respectively. SMRs in both stacks perform similarly, showing coupling coefficient (k2) of 2.0%, series Q (Qs) of 156, and parallel Q (Qp) values of 140 for Ta2O5/SiO2, while k2 of 2.4%, Qs of 140, and Qp of 109 for Nb2O5/SiO2, both at 18.6 GHz. Upon development, ScAlN solidly mounted platforms will enable signal processing elements with better power handling.
2 April 2026 in IEEE Transactions on Ultrasonics
Piezoelectric micromachined ultrasonic transducers (PMUTs) are widely utilized in applications that demand mechanical resilience, thermal stability, and compact form factors. Recent efforts have sought to demonstrate that single-crystal lithium niobate (LN) is a promising PMUT material platform, offering high electromechanical coupling (k2) and bidi-rectional performance. In addition, advances in LN film transfer technology have enabled high quality periodically poled piezoelectric films (P3F), facilitating a bimorph piezoelectric stack without intermediate electrodes. In this work, we showcase a bimorph PMUT incorporating a mechanically robust, 20 μm thick P3F LN active layer. We establish the motivation for LN PMUTs through a material comparison, followed by extensive membrane geometry optimization and subsequent enhancement of the PMUT’s k2. We demonstrate a 775 kHz flexural mode device with a quality factor (Q) of 200 and an extracted k2 of 6.4%, yielding a high transmit efficiency of 65 nm/V with a mechanically robust active layer. We leverage the high performance to demonstrate extreme-temperature resilience, showcasing stable device operation up to 600 °C and survival up to 900 °C, highlighting LN’s potential as a resilient PMUT platform.