Borja Lizarribar Carrillo

Mr. Borja Lizarribar Carrillo

CEIT-Basque Research and Technology Alliance, San Sebastian, Spain
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 February 2024 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
BCBorja Lizarribar Carrillo
Borja Lizarribar Carrillo
BPBorja Prieto
Borja Prieto
Ahmed SelemaAhmed Selema
Ahmed Selema
Mohamed IbrahimMohamed Ibrahim
Mohamed Ibrahim
PSPeter Sergeant
Peter Sergeant
MMMiguel Martinez-Iturralde
Miguel Martinez-Iturralde
This paper proposes loss & thermally optimised copper and aluminium structures for automotive electrical machines. A first batch of multiphysics optimisation is performed parametrically for 6 different electrical conductor topologies. Then, a multiphysics – thermal and electromagnetic – hybrid parametric and topology optimisation coupled with Multi Objective Differential Evolution (MODE) and with an additional step of Local Search (LS) is proposed. The introduced Topology Optimisation (TO) algorithm is explained in detail and applied to optimise electrical conductor geometries of pure Cu and AlSi10Mg. After that, the manufacturing by Additive Manufacturing (AM) of the most promising model is presented. The produced topology is benchmarked against a well-known fully rectangular structure. The proposed topology optimised geometry has been found to improve conventionally manufactured electrical conductors at intermediate frequencies, around 600-800 Hz, and improves considerably at high frequencies, achieving a reduction in losses of 58% at 2000 Hz comparing to a conventional rectangular copper structure.

23 June 2022 in IEEE Access
Verified
Journal Article
Open access
BCBorja Lizarribar Carrillo
Borja Lizarribar Carrillo
BPBorja Prieto
Borja Prieto
MMMiguel Martinez-Iturralde
Miguel Martinez-Iturralde
GBGurutz Artetxe Ballejo
Gurutz Artetxe Ballejo
This paper proposes a combined electromagnetic and mechanical topology optimization for weight reduction in electrical machines based on Finite Element Analysis (FEA) and Evolutionary Structural Optimization (ESO). The devised method is an on- off-type algorithm with adaptative mesh in which low flux density and low Von Mises stress cells are removed successively from a first machine design. With this approach, the weight of the machine can be considerably reduced without compromising the electromagnetic performance of the machine, with a reduced computation time compared to other topology optimization methods. A case study involving a 1.2 MW low-speed, permanent magnet motor is analyzed under different conditions (algorithm parameters, initial mesh, rotational speed) and used to compare the proposed method with two other topology optimization approaches.

17 September 2023 in Aerospace
Verified
Journal Article
Open access
PDF file
BCBorja Lizarribar Carrillo
Borja Lizarribar Carrillo
BPBorja Prieto
Borja Prieto
Miren AristizabalMiren Aristizabal
Miren Aristizabal
JMJOSE MANUEL MARTIN
JOSE MANUEL MARTIN
MMMiguel Martinez-Iturralde
Miguel Martinez-Iturralde
SMSergio Montes
Sergio Montes
Recent advances in manufacturing methods have accelerated the exploration of new materials and advantageous shapes that could not be produced by traditional methods. In this context, additive manufacturing is gaining strength among manufacturing methods for its versatility and freedom in the geometries that can be produced. Taking advantage of these possibilities, this research presents a case study involving an electric aerospace actuator manufactured using additive manufacturing. The main objectives of this research work are to assess the feasibility of additively manufacturing electric actuators and to evaluate potential gains in terms of weight, volume, power consumption and cost over conventional manufacturing technologies. To do so and in order to optimise the actuator design, a thorough material study is conducted in which three different magnetic materials are gas-atomised (silicon iron, permendur and supermalloy) and test samples of the most promising materials (silicon iron and permendur) are processed by laser powder bed fusion. The final actuator design is additively manufactured in permendur for the stator and rotor iron parts and in 316L stainless steel for the housing. The electric actuator prototype is tested, showing compliance with design requirements in terms of torque production, power consumption and heating. Finally, a design intended to be manufactured via traditional methods (i.e., punching and stacking for the stator laminations and machining for the housing) is presented and compared to the additively manufactured design. The comparison shows that additive manufacturing is a viable alternative to traditional manufacturing for the application presented, as it highly reduces the weight of the actuator and facilitates the assembly, while the cost difference between the two designs is minimal.

21 June 2024 in Open Research Europe
Verified
Journal Article
Open access
BCBorja Lizarribar Carrillo
Borja Lizarribar Carrillo
BPBorja Prieto
Borja Prieto
MMMiguel Martínez-Iturralde
Miguel Martínez-Iturralde
JGJavier García Goikoetxea
Javier García Goikoetxea
SMSergio Montes
Sergio Montes
EJEkain San José
Ekain San José
Background The ambitious electrification targets set for the aeronautical sector are leading to a thorough research into improving the performance of different electromechanical components. In this regard, Additive Manufacturing is gaining strength due to the positive physical properties of the processed parts and the freedom in manufacturable geometries. Methods Thus, this article presents the design of an electric actuator for an aerospace active sidestick in which Additive Manufacturing is used with the aim of minimising the weight and power consumption of the device. The electromagnetic design of the actuator is detailed, considering 8 different permanent magnet machine topologies, and a mechanical design applying Topology Optimisation to reduce the overall weight of the component is carried out. Results Three prototypes involving the rotor, the stator and the casing are manufactured via Laser Powder Bed Fusion in stainless steel and Permendur (Fe 49Co 49V 2) and the corresponding actuators are experimentally tested, showing a great agreement between tests and simulations and excellent repeatability in the electromagnetic behaviour of the prototypes. Conclusions The research results highlight the great potential of Additive Manufacturing to manufacture functional electrical machine components.

22 September 2025 in IEEE Access
Verified
Journal Article
Open access
PAPablo Alvarez
Pablo Alvarez
MSMarco Satrústegui
Marco Satrústegui
BCBorja Lizarribar Carrillo
Borja Lizarribar Carrillo
MMMiguel Martinez-Iturralde
Miguel Martinez-Iturralde
This paper presents a promising winding technique that enables higher power densities in high-temperature superconducting (HTS) electrical machines with a slotless stator, such as self-supporting windings. The concept of helical winding is first defined, followed by an explanation of the skew angle and how different winding configurations can be characterized as a function of this angle. A case study is then conducted to select the most suitable helical winding for a specific 2 MW HTS electric motor. Finally, the manufacturing and testing of the helical winding configuration for electric aircraft propulsion are evaluated, comparing the active part weight of the machine with its power density.

25 February 2025 in Open Research Europe
Verified
Journal Article
Open access
BCBorja Lizarribar Carrillo
Borja Lizarribar Carrillo
BPBorja Prieto
Borja Prieto
MMMiguel Martínez-Iturralde
Miguel Martínez-Iturralde
JGJavier García Goikoetxea
Javier García Goikoetxea
SMSergio Montes
Sergio Montes
EJEkain San José
Ekain San José
Background The ambitious electrification targets set for the aeronautical sector are leading to a thorough research into improving the performance of different electromechanical components. In this regard, Additive Manufacturing is gaining strength due to the positive physical properties of the processed parts and the freedom in manufacturable geometries. Methods Thus, this article presents the design of an electric actuator for an aerospace active sidestick in which Additive Manufacturing is used with the aim of minimising the mass and power consumption of the device. The electromagnetic design of the actuator is detailed, considering 8 different permanent magnet machine topologies, and a mechanical design applying Topology Optimisation to reduce the overall mass of the component is carried out. Results Three prototypes involving the rotor, the stator and the casing are manufactured via Laser Powder Bed Fusion in stainless steel and Permendur (Fe 49Co 49V 2) and the corresponding actuators are experimentally tested, showing a great agreement between tests and simulations and excellent repeatability in the electromagnetic behaviour of the prototypes. Conclusions The research results highlight the great potential of Additive Manufacturing to manufacture functional electrical machine components.