A 1D MEMS (Micro-Electro-Mechanical Systems) mirror for LiDAR applications, based on vertically asymmetric comb-drive electrostatic actuators, is presented in this work employing a novel fabrication process. This novel micromachining process combines typical SOI-based bulk micromachining and grayscale lithography, enabling the fabrication of combs actuators with asymmetric heights using a single lithography step in the active layer. With this technique, the fabrication process is simplified, and the overall costs are reduced since the number of required lithography steps decrease. The fabricated mirrors present self-aligned electrodes with a 2.8 μm gap and asymmetric heights of the movable and the fixed electrodes of 20 μm and 50 μm, respectively. These asymmetric actuators are an essential feature for the operation mode of this device, enabling both in resonant and static mode operation. A mirror field of view (FOV) of 54° at 838 Hz was achieved under low-pressure, when resonantly operated, and a FOV of 0.8° in the static mode.
An open-source tool that allows for a fast and precise analytical calculation of multi-layer planar coils self-inductance, without any geometry limitation is proposed here. The process of designing and simulating planar coils to achieve reliable results is commonly limited on accuracy and or geometry, or are too time-consuming and expensive, thus a tool to speed up this design process is desired. The model is based on Grover equations, valid for any geometry. The validation of the tool was performed through the comparison with experimental measurements, Finite Element Model (FEM) simulations, and the main analytical methods usually used in literature, with errors registered to be below , when compared to standard FEM simulations, and when compared to experimental measurements they are below in the case of the 1-layer coils, and below in the 2-layer coils (without taking into consideration the coil connectors). The proposed model offers a new approach to the calculation of the self-inductance of planar coils of several layers that combines precision, speed, independence of geometry, easy interaction, and no need for extra resources.
The uniqueness of microelectromechanical system (MEMS) devices, with their multiphysics characteristics, presents some limitations to the borrowed test methods from traditional integrated circuits (IC) manufacturing. Although some improvements have been performed, this specific area still lags behind when compared to the design and manufacturing competencies developed over the last decades by the IC industry. A complete digital solution for fast testing and characterization of inertial sensors with built-in actuation mechanisms is presented in this paper, with a fast, full-wafer test as a leading ambition. The full electrical approach and flexibility of modern hardware design technologies allow a fast adaptation for other physical domains with minimum effort. The digital system encloses a processor and the tailored signal acquisition, processing, control, and actuation hardware control modules, capable of the structure position and response analysis when subjected to controlled actuation signals in real time. The hardware performance, together with the simplicity of the sequential programming on a processor, results in a flexible and powerful tool to evaluate the newest and fastest control algorithms. The system enables measurement of resonant frequency (Fr), quality factor (Q), and pull-in voltage (Vpi) within 1.5 s with repeatability better than 5 ppt (parts per thousand). A full-wafer with 420 devices under test (DUTs) has been evaluated detecting the faulty devices and providing important design specification feedback to the designers.
The growing urbanization of modern societies intensifies the demand for sustainable mobility that aligns efficiency, safety, and environmental responsibility in smart cities. Shared vehicle systems address this need, but remain limited by subjective manual inspections that hinder operational efficiency. Automated exterior damage assessment via computer vision offers a scalable alternative, although its success critically depends on high-quality, domain-specific datasets, which remain scarce. To overcome this limitation, we introduce SYNDCAR (SYNthetic Damage CAR dataset), a generative AI-based dataset that simulates realistic vehicle damage in images with precise annotations for detection and vehicle parts segmentation. Extensive experiments were conducted that covered hyperparameter tuning, transfer learning, benchmarking of CNN- and Transformer-based models, and post-training optimization and quantization. The results highlight the challenges of damage detection due to appearance variability and dataset size, while pointing to practical solutions: YOLOv8-X achieved the highest accuracy, whereas YOLOv12-S provided the best trade-off. TensorRT deployment tests (FP16/INT8) further reduced the inference time by ≈ 71% on the GPU and the energy consumption by 65%. Segmentation remained more energy-intensive than detection. In general, SYNDCAR demonstrates the potential of synthetic datasets to enable accurate, efficient, and scalable vehicle inspection systems.
This paper presents a highly tunable low-g microelectromechanical systems (MEMS) inertial switch. The switch is specifically designed as a low-power wake-up device for Internet-of-Things (IoT) applications. The designed inertial switch is sensitive to in-plane accelerations in all directions (omnidirectional). The proposed inertial switch has been modeled and simulated both analytically and using finite element analysis techniques. The switch prototype has been fabricated through an in-house optimized silicon-on-insulator (SOI) wafer process, which allows patterning on both the device and handle silicon layers. The fabricated inertial switch was experimentally tested using a closed-loop shaker system to measure acceleration thresholds and a tilt stage for electrical resistance measurements. This inertial switch demonstrates the ability to tune the acceleration threshold in a wide range of 0.25 g to 2 g. This promising inertial sensor holds a significant potential for applications requiring a high dynamic range for acceleration threshold detection, such as mechanical wake-up functions in IoT devices.