Fulvia FULVIA

Dr. Fulvia FULVIA

ENEA - Italian National Agency for New Technologies, Energy and Sustainable Economic Development, Brindisi, Puglia, Italy
orcid

Research Focus & Metrics

Academic Career Length

34Years (1993-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 July 2009 in The Journal of Physical Chemistry C
Verified
Journal Article
Closed access
FFFulvia FULVIA
Fulvia FULVIA
PVPaolo Vacca
Paolo Vacca
GNGiuseppe Nenna
Giuseppe Nenna
OVOlga Valentino
Olga Valentino
GBGianbattista Burrasca
Gianbattista Burrasca
DSDario della Sala
Dario della Sala

21 September 2016 in Scientific Reports
Verified
Journal Article
Open access
ESEnrico Sowade
Enrico Sowade
Eloi RamonEloi Ramon
Eloi Ramon
KMKalyan Yoti Mitra
Kalyan Yoti Mitra
Carme Martinez-DomingoCarme Martinez-Domingo
Carme Martinez-Domingo
MPMarta Pedró
Marta Pedró
RBReinhard R. Baumann
Reinhard R. Baumann
We report on the detailed electrical investigation of all-inkjet-printed thin-film transistor (TFT) arrays focusing on TFT failures and their origins. The TFT arrays were manufactured on flexible polymer substrates in ambient condition without the need for cleanroom environment or inert atmosphere and at a maximum temperature of 150 °C. Alternative manufacturing processes for electronic devices such as inkjet printing suffer from lower accuracy compared to traditional microelectronic manufacturing methods. Furthermore, usually printing methods do not allow the manufacturing of electronic devices with high yield (high number of functional devices). In general, the manufacturing yield is much lower compared to the established conventional manufacturing methods based on lithography. Thus, the focus of this contribution is set on a comprehensive analysis of defective TFTs printed by inkjet technology. Based on root cause analysis, we present the defects by developing failure categories and discuss the reasons for the defects. This procedure identifies failure origins and allows the optimization of the manufacturing resulting finally to a yield improvement.


3 January 2020 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
Daniele ValeriniDaniele Valerini
Daniele Valerini
LTLoredana Tammaro
Loredana Tammaro
FFFulvia FULVIA
Fulvia FULVIA
Antonella RizzoAntonella Rizzo
Antonella Rizzo
ICIvana Caputo
Ivana Caputo
Giovanni VigliottaGiovanni Vigliotta
Giovanni Vigliotta

1 February 2000 in Journal of Photochemistry and Photobiology B: Biology
Verified
Journal Article
Closed access
ACAlberto Colasanti
Alberto Colasanti
AKAnnamaria Kisslinger
Annamaria Kisslinger
RLRaffaele Liuzzi
Raffaele Liuzzi
MQMaria Quarto
Maria Quarto
PRPatrizia Riccio
Patrizia Riccio
FFFulvia FULVIA
Fulvia FULVIA

28 May 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Andrés Lopez GarciaAndrés Lopez Garcia
Andrés Lopez Garcia
GSGiuliano Sico
Giuliano Sico
MMMaria Montanino
Maria Montanino
VDViktor Defoor
Viktor Defoor
MPManojit Pusty
Manojit Pusty
Gustavo ArdilaGustavo Ardila
Gustavo Ardila
Zinc oxide (ZnO) nanowires (NWs) are excellent candidates for the fabrication of energy harvesters, mechanical sensors, and piezotronic and piezophototronic devices. In order to integrate ZnO NWs into flexible devices, low-temperature fabrication methods are required that do not damage the plastic substrate. To date, the deposition of patterned ceramic thin films on flexible substrates is a difficult task to perform under vacuum-free conditions. Printing methods to deposit functional thin films offer many advantages, such as a low cost, low temperature, high throughput, and patterning at the same stage of deposition. Among printing techniques, gravure-based techniques are among the most attractive due to their ability to produce high quality results at high speeds and perform deposition over a large area. In this paper, we explore gravure printing as a cost-effective high-quality method to deposit thin ZnO seed layers on flexible polymer substrates. For the first time, we show that by following a chemical bath deposition (CBD) process, ZnO nanowires may be grown over gravure-printed ZnO nanoparticle seed layers. Piezo-response force microscopy (PFM) reveals the presence of a homogeneous distribution of Zn-polar domains in the NWs, and, by use of the data, the piezoelectric coefficient is estimated to be close to 4 pm/V. The overall results demonstrate that gravure printing is an appropriate method to deposit seed layers at a low temperature and to undertake the direct fabrication of flexible piezoelectric transducers that are based on ZnO nanowires. This work opens the possibility of manufacturing completely vacuum-free solution-based flexible piezoelectric devices.