Jaume Girona-Badia

Mr. Jaume Girona-Badia

UPC
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 March 2024 in IEEE Access
Verified
Journal Article
Open access
MRMuhammad Waleed Raza
Muhammad Waleed Raza
MRMuhammad Raza
Muhammad Raza
Jaume Girona-BadiaJaume Girona-Badia
Jaume Girona-Badia
Eduardo Prieto-AraujoEduardo Prieto-Araujo
Eduardo Prieto-Araujo
Oriol Gomis-BellmuntOriol Gomis-Bellmunt
Oriol Gomis-Bellmunt
Offshore wind power generation equipped with conventional grid following controls challenges the power system stability by reducing the inertia of the grid and weakening the AC offshore grid. To overcome this vulnerability a promising solution could be equipping the wind turbines with grid-forming (GFM) control schemes. Many methodologies have been presented in the literature for GFM inverters. In spite of this, their applications for WTGs have not been thoroughly explored. This paper presents the study of fault handling capability of wind turbines with several grid-forming control strategies. In this context, four different control schemes i.e. Visynch, P/f droop, Q/f droop and conventional grid following control are considered. The performance of these control strategies is assessed and compared during a three-phase symmetrical fault on the point of common coupling of an offshore wind farm. A case study which consists of two wind turbines connected to the main converter of an offshore substation equipped with grid-forming control is also considered. The results indicate that, during faults, each of the four control strategies (Visynch, P/f droop, Q/f droop, and Gfol) effectively limits the current and restores normal operation. A significant advantage of Q/F droop control is its reduced sensitivity to variations in system and fault parameters, adjustable frequency response, and independence from existing Phase-Locked Loops (PLLs). On the other hand, the P/f droop control provides greater voltage support during faults due to its voltage controllers. However, post-fault oscillations result from the stiff voltage controller. Visynch control, on the other hand, shows a lower margin of stability. The advantages and weaknesses of each control scheme is revealed using the simulation results.

28 November 2023 in International Journal of Electrical Power & Energy Systems
Verified
Journal Article
Open access
Jaume Girona-BadiaJaume Girona-Badia
Jaume Girona-Badia
Eduardo Prieto-AraujoEduardo Prieto-Araujo
Eduardo Prieto-Araujo
Oriol Gomis-BellmuntOriol Gomis-Bellmunt
Oriol Gomis-Bellmunt

28 February 2023 in Global Challenges
Verified
Journal Article
Open access
CCCarlos Collados‐Rodríguez
Carlos Collados‐Rodríguez
EAEduard Antolí‐Gil
Eduard Antolí‐Gil
ESEnric Sánchez-Sánchez
Enric Sánchez-Sánchez
Jaume Girona-BadiaJaume Girona-Badia
Jaume Girona-Badia
VLVinícius Albernaz Lacerda
Vinícius Albernaz Lacerda
Oriol Gomis-BellmuntOriol Gomis-Bellmunt
Oriol Gomis-Bellmunt
Recent environmental policies have led academic, industrial, and governmental stakeholders to plan scenarios with a high share of renewable energy sources (RES), to ensure that future energy systems, composed mostly of RES, can remain stable, match the demand during seasonal variations and are economically feasible. This article considers different energy scenarios to obtain various options in terms of size, generation technologies, and grid configuration. The scenarios are studied in the POSYTYF project and are quantified through an optimization‐based algorithm, where the test grids topologies are based on specific locations in Europe, and real data related to the availability of RES, as well as the demand. Different RES technologies are considered to meet requirements of grid integration of renewables at different horizons of time, up to 100% in the most futuristic case. The optimization algorithm is applied to three scenarios. It is shown that solar photovoltaic (PV) and wind can provide the renewable backbone, but they lack flexibility to achieve a very high share in the energy mix. Solar thermal and pumped hydro become important to cover the last range of integration, as they provide high flexibility, which is crucial for high share, but they are expensive for low share.

24 October 2024 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
Jaume Girona-BadiaJaume Girona-Badia
Jaume Girona-Badia
VLVinícius Albernaz Lacerda
Vinícius Albernaz Lacerda
DSDaniel Westerman Spier
Daniel Westerman Spier
Eduardo Prieto-AraujoEduardo Prieto-Araujo
Eduardo Prieto-Araujo
Oriol Gomis-BellmuntOriol Gomis-Bellmunt
Oriol Gomis-Bellmunt
This paper presents a power-synchronization loop scheme for renewable power generation operated in Grid-Forming (GFM), which considers the DC-connected resource limitations. Under conditions where the resource might not be able to provide the Alternating Current (AC) power required by the GFM structure (e.g. lack of resource), the DC voltage might drop to concerning low values, leading to potential converter shutdowns. The proposed resource-aware GFM (RAGFM) is capable of regulating the DC bus while maintaining a GFM behaviour towards the AC network. The control is analyzed for the two operating modes of the inverter-based resources (IBRs).In the first, the resource provides constant power, whereas the second mode considers that the resource operates with a power reserve. The tuning of the different gains of the suggested control scheme is defined based on the maximum virtual inertia that the converter can emulate without exceeding its design limitations. In addition, RAGFM is benchmarked against other synchronization methods, including a detailed dynamic analysis. The different synchronization methods are analytically and dynamically compared. Finally, the RAGFM is implemented in an experimental set-up where its capabilities are verified.

1 March 2022 in Energies
Verified
Journal Article
Open access
PDF file
Jaume Girona-BadiaJaume Girona-Badia
Jaume Girona-Badia
Oriol Gomis-BellmuntOriol Gomis-Bellmunt
Oriol Gomis-Bellmunt
TPTomàs Lledó Ponsati
Tomàs Lledó Ponsati
MLMacià Capó Lliteras
Macià Capó Lliteras
CCCarlos Collados-Rodriguez
Carlos Collados-Rodriguez
Eduardo Prieto-AraujoEduardo Prieto-Araujo
Eduardo Prieto-Araujo
Modular multilevel converters (MMC) can be used in several applications, especially (but not only) in high-voltage direct current (HVDC) and STATCOM. In order to develop experimental scaled-down test benches for lab validation, several projects have developed MMCs with a limited number of cells, but they need to use pulse width modulation (PWM) techniques to achieve acceptable power quality (because nearest level modulation (NLM), common in HVDC applications with hundreds of levels, cannot achieve sufficient power quality unless the number of cells is high enough). The present paper proposes a new concept which is based on designing arms with a single cell. This allows to have the simplest possible converter that maintains the structure of an MMC. While all the inner controllers of large-scale HVDC MMCs are included, the only remarkable difference is that PWM is used and NLM cannot be implemented. As this is also a limitation for other low voltage MMC, the proposed concept is suggested for scaled-down low voltage applications. The paper includes the design and construction of the converter, the definition and implementation of the converter controllers, and the converter testing, with detailed dynamic simulations and an experimental setup.

30 October 2025 in IEEE Access
Verified
Journal Article
Open access
MTMohammadhossein Tavanaee
Mohammadhossein Tavanaee
Jaume Girona-BadiaJaume Girona-Badia
Jaume Girona-Badia
Marc Cheah MañéMarc Cheah Mañé
Marc Cheah Mañé
Oriol Gomis-BellmuntOriol Gomis-Bellmunt
Oriol Gomis-Bellmunt
Eduardo Prieto-AraujoEduardo Prieto-Araujo
Eduardo Prieto-Araujo
The growing demand for efficient and sustainable hydrogen production highlights the need for converter topologies that comply with grid code requirements and contribute toward the stability of the power system in electrolysis applications. In this paper, several converter topologies are reviewed and analyzed based on the performance of the most common electrolyzers, PEM and AEL. Traditional diode and thyristor-based rectifiers are explored, emphasizing their reliability and robustness while highlighting their flexibility limitations. IGBT-based power converters are also introduced, demonstrating their potential for electrolysis applications with faster response times and improved power quality. A comprehensive comparative analysis under steady-state and fault conditions is presented, offering critical insights into the converter choices for future large-scale hydrogen production.