The prompt and robust detection of tactile information is a relevant and challenging problem, and a considerable research effort is thus being put into innovative transduction methods for tactile sensors. In this paper, we investigate the possibility of using event-based cameras to sense contact forces applied to objects by a robot end effector. The proposed optical tactile sensor incorporates a soft hemispherical pad made of silicone rubber with imprinted markers and a PWM light source that emits optical pulses, allowing robust detection of the markers to track deformations of the pad. To test the effectiveness of our sensor, experiments were carried out attaching it to a teleoperated robot arm to finely control it when out of the user's field of view, as accurately as if the user could see it. In the experiments, an augmented reality display and a haptic device were used to convey the force detected by the event-based tactile sensor back to the human operator. The experiments included a practical application of a soft tissue puncturing tool, and psychophysical test results from ten participants were recorded, to validate efficacy and usability of the system.
Fiber-optic sensors are a powerful tool to investigate physical properties like temperature, strain, and pressure. Such properties make these sensors interesting for many applications including biomedical applications. Fiber sensors are also a great platform for distributed sensing by using the principles of optical frequency domain reflectometry. Distributed sensing is becoming more and more used to achieve high-resolution measurements and to map physical properties of biomaterials at small scale, thus obtaining 2D and 3D mapping of a particular area of interest. This work aims at building and investigating a 2D sensing carpet based on a distributed fiber sensing technique, to map local pressure applied to the carpet. The two-dimensional mapping is obtained by embedding a single-mode optical fiber inside a soft silicone carpet. The fiber has been bent and arranged in a specific configuration characterized by several parallel lines. Different fiber fixation methods have been investigated by means of a comparative analysis to perform better characterization and to achieve a more precise response of the carpet. The best pressure sensitivity coefficient (0.373 pm/kPa or considering our setup 1.165 nm/kg) was detected when the fiber was fully embedded inside the silicone carpet. This paper demonstrates the possibility of mapping a 2D distributed pressure over a surface with a resolution of 2 mm by 2 mm. The surface of investigation is 2 cm by 6 cm, containing 310 sensing points. The sensing carpet has been validated selecting several preferential positions, by testing the consistency of the results over different portions of the carpet.
Bite force measurements are crucial in the realm of biomedical research, particularly in the areas of dentistry and orthodontic care. Various intraoral devices have been used to assess biting force, but each has limitations and drawbacks. Fiber optic sensors (FOSs) offer advantages such as electrical inertness, immunity to electromagnetic interference, and high sensitivity. Distributed fiber optic sensing allows an increase in the number of sensing points and can interrogate numerous reflections from scattering events within an optical fiber. We present four dental bites with heights of 6 mm, which enabled bilateral measurements. U-shaped sensors were prepared by embedding fibers into silicone by folding a single-mode fiber into four lines and multiplexing eight parallel nanoparticle-doped fibers. Dental bite models were created using two silicone materials (Sorta Clear 18 and Sorta Clear 40). The developed sensors were calibrated by applying weights up to 900 g, resulting in a linear response. Experiments were conducted to compare the efficacy of the dental bites. The collection of massive data was enabled by constructing a 2D map of the dental bites during multi-point sensing.
While most tactile sensors rely on measuring pressure, insights from continuum mechanics suggest that measuring shear strain provides critical information for tactile sensing. In this work, we introduce an optical tactile sensing principle based on shear strain detection. A silicone rubber layer, dyed with color inks, is used to quantify the shear magnitude of the sensing layer. This principle was validated using the NUSense camera-based tactile sensor. The wide-angle camera captures the elongation of the soft pad under mechanical load, a phenomenon attributed to the Poisson effect. The physical and optical properties of the inked pad are essential and should ideally remain stable over time. We tested the robustness of the sensor by subjecting the outermost layer to multiple load cycles using a robot arm. Additionally, we discussed potential applications of this sensor in force sensing and contact localization.
Measuring bite force gives important information about the performance of the jaw muscles. Enhancement of bite force measurements, particularly 2D force mapping, can be achieved through the application of advanced distributed fiber optics sensing techniques, which present the capability to acquire high resolution measurements. Optical Backscatter Reflectometry (OBR), based on the principles of Optical Frequency Domain Reflectometry (OFDR), is the key to achieve spatially distributed measurements and transform a single-mode fiber (SMF) into a cost-effective minimally invasive sensor. The OBR interrogator, manufactured by LUNA, catches the light backscattered by each section of the fiber and detects the spectral variation induced by the stain and pressure application. We have developed two methods to construct a two-dimensional map of the applied bite force. In the first a SMF has been bent into four lines and embedded into a silicone mouthguard. In the second approach we used massive Scattering‑Level Multiplexing (SLMux), which exploits fibers with different scattering levels: a standard low scattering SMF to enable the multiplexing, and a MgO‑nanoparticles doped fibers with a 40 dB higher scattering for sensing purposes. The setup with eight multiplexed fibers allows to obtain bite force mapping for each side of the jaw by embedding four fibers for left and right sides. The pressure sensitivity coefficient of the maps has been effectively calculated. The setup has been validated for 2D force mapping over the silicone mouthguard with millimeter resolution. The capability of optical fiber to be multiplexed and embedded in non-uniform geometries results in a high resolved and precise 2D bite force reconstruction.