In this article, we propose an analysis and controller design of a bidirectional bridgeless single-stage dc/ac converter with high-frequency link and low part count. The dual-phase-shift control is proposed to control and modulate the ac power and to minimize the root mean square (rms) of the transformer current. Furthermore, the phase-shift angle is chosen to assure wide range of zero voltage switching (ZVS) turn- on of all the switching devices. The proposed controller has a reduced total harmonic distortion (THD) at the output ac current without zero-crossing spikes. A continuous-time average model that well predicts both transient- and steady-state relations between the high-frequency ac link and the dc side is needed to simplify the controller design. Since complex discrete-time models were used in the previous pieces of literature, simple and powerful continuous-time tools were not used to design the closed-loop system. In this article, a novel continuous-time generalized average model is proposed. The derived model precisely predicts the high-frequency state variables of the converter, including a simple formula for the transformer current rms value. The formula is used to minimize the transformer current to reduce the losses. Moreover, the transient analysis and the closed-loop control design are presented. A prototype circuit is tested to verify the performance of the proposed control scheme with the proposed isolated single-stage dc/ac converter.
1 November 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This article proposes a single stage AC/AC converter with a high frequency-link which is suitable for multi-level converters. The proposed topology is a direct AC/AC converter without commutation problems which solves the common issue of direct AC/AC converters. Moreover, four-quadrant switches commonly used in matrix converters, and unfolding bridges normally essential in conventional circuits, are unnecessary in the proposed circuit, which enhances the efficiency and cost. The converter control strategy is adapted based on a single-phase shift technique with constant switching frequency and 50% duty cycle. The control strategy achieves a wide range of ZVS turn-on without any auxiliary circuit. Furthermore, the high-frequency transformer (HFT) is free from line-frequency components with minimized RMS value of current. Hence, a HFT with reduced size can be realized. The converter also has a low THD load current. A new continuous-time transient model of the proposed converter is proposed based on the Generalized Average Model (GAM). The derived model is used to design the proposed phase-shift controller. Moreover, a detailed closed-loop transient analysis is presented. A prototype circuit is implemented to validate the theoretical analysis and the feasibility of the proposed converter.
27 March 2023 in IEEE Transactions on Instrumentation and Measurement
In the last few years, the switching frequency of power electronic converters is extended to the several MHz range. ISM frequency bands are specified in this range for power electronic applications. Most converter circuits, such as resonance and soft-switching circuits require an accurate modeling of the circuit components, such as the high frequency inductors and transformers. This paper focuses on the evaluation of a practically simple but accurate high frequency transformer model. In first, a three-capacitor lumped model is chosen due to its simplicity as well as to the physics-oriented concept. Furthermore, the extraction of the parameters is straightforward. It is found that splitting the leakage inductances in two halves based on the winding capacitance would make the model more accurate for modeling high frequency characteristics. The paper analyzes the model and provides a closed form transfer function for the input impedance and the voltage gain. To verify the model, different kinds of transformer hardware are fabricated, and their input impedances are measured from 1 MHz to 30 MHz, which includes three ISM bands. The measurements are then compared with the impedance function developed from the model. The model shows well-matching with the measurement as compared to the conventional models. Finally, the model is validated experimentally by designing an isolated 13.56 MHz Class-E power conversion circuit, which includes a transformer with soft-switching. The soft-switching is designed based on the conventional, three-capacitor and the proposed model, respectively. The proposed model provides more accurate design for the inverter assuring soft-switching and optimum performance of the circuit.
5 December 2023 in Journal of Electrical Engineering & Technology
A zero-voltage zero-current-switching (ZVZCS) full-bridge DC-DC converter, based on a dual transformer with two output filter capacitors, is proposed in this paper. The proposed topology is suitable for application in renewable energy at medium voltage, integrated with a DC collection system. To realize voltage and power regulation for the converter, pulse width modulation (PWM) is employed with a fixed duty cycle for the main switches. Through careful design of the turns ratio of the main transformer, most of the power under full load range is delivered by the main full-bridge circuit, which also achieves zero-voltage switching (ZVS). This significantly reduces the switching losses. A small portion of the total power is delivered by the auxiliary circuit that realizes ZVZCS. Therefore, the turns ratio of the auxiliary transformer can be optimized such that the efficiency of the proposed converter can be improved. The optimzation is discussed in detail, along with the design parameters of the proposed converter. A prototype of 200V-2kV/3kW has been developed to verify the simulation results and validate the working of the proposed scheme.
The advantages offered by DC microgrids, such as elimination of skin effect losses, no requirement of frequency synchronization and high efficiency for power transmission are the major reasons that microgrids have attracted the attention of researchers in the last decade. Moreover, the DC friendly nature of renewable energy resources makes them a perfect choice for integration with DC microgrids, resulting in increased reliability and improved stability. However, in order to integrate renewable energy resources with the DC microgrids, challenges like equal load sharing and voltage regulation of the busbar under diverse varying load conditions are to be addressed. Conventionally, droop control with PI compensation is used to serve this purpose. However, this cascaded scheme results in poor regulation to large load variations and steady state errors. To address this issue, this paper presents a sliding mode control-based approach. Key features of SMC are its ease of implementation, robustness to load variations, and fast dynamic response. The system model is derived and simulated to analyze the stability and performance of the proposed controller. An experimental test bench is developed to demonstrate the effectiveness of SMC against modeled dynamics and is compared with the droop controller. The results show an improvement of and in the rise time and settling time, respectively. Robustness of the proposed scheme is also tested by switching it with a step load and an improvement of has been observed.