PANDI MAHARAJAN M

Dr. PANDI MAHARAJAN M

ECE, Saveetha School of Engineering, Saveetha Institute of Medical And Technical Sciences, Chennai, India
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 November 2018 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
PMPANDI MAHARAJAN M
PANDI MAHARAJAN M
SXS. Arockia Edwin Xavier
S. Arockia Edwin Xavier
It is a very difficult process to achieve smooth drivers for the motor operating under variable speed mode. In brushless direct current motor (BLDC) when back electromotive force (BEMF) waveform is of trapezoidal type, the developed torque is constant in ideal conditions. However, practically torque ripple presents in the output torque because of the physical design of the motor and its parameters. Also, the produced ripples are associated with the control and driver side of the motor. In the previous literature, the drive without a dc link capacitor is presented but the torque ripple reduction is not effective. Hence in another work, the usage of the small capacitor is recommended and the results are improved. In this work, the quick stabilization with torque ripple reduction is presented using a bio-inspired algorithm-based technique in a Brushless DC (BLDC) motor drive. A Spider based controller is built to generate the pulse width modulation signals to the inverter and the control signal applied to the capacitor. The effect of utilizing small DC link capacitor, on the torque ripple reduction and speed control is investigated. The performance is also compared with the case of large capacitor utilization and without a capacitor case is verified experimentally by dsPIC30F4011 hardware circuit.

19 January 2024 in Sustainability
Verified
Journal Article
Open access
PDF file
KBKARTHIKEYAN B
KARTHIKEYAN B
PRPalanisamy Ramasamy
Palanisamy Ramasamy
PMPANDI MAHARAJAN M
PANDI MAHARAJAN M
PNPadmamalini Narasimhalu
Padmamalini Narasimhalu
JSJ. Sivakumar
J. Sivakumar
GEORGE FERNANDEZ SAVARIGEORGE FERNANDEZ SAVARI
GEORGE FERNANDEZ SAVARI
The fossil fuel crisis is a major concern across the globe, and fossil fuels are being exhausted day by day. It is essential to promptly change from fossil fuels to renewable energy resources for transportation applications as they make a major contribution to fossil fuel consumption. Among the available energy resources, a fuel cell is the most affordable for transportation applications because of such advantages as moderate operating temperature, high energy density, and scalable size. It is a challenging task to optimize PEMFC operating parameters for the enhancement of performance. This paper provides a detailed study on the optimization of PEMFC operating parameters using a multilayer feed-forward neural network, a genetic algorithm, and the design of a multiport high-gain DC–DC converter for hybrid electric vehicle application, which is capable of handling both a 6 kW PEMFC and an 80 AH 12 V heavy-duty battery. To trace the maximum power from the PEMFC, the most recent SFO-based MPPT control technique is implemented in this research work. Initially, a multilayer feed-forward neural network is trained using a back-propagation algorithm with experimental data. Then, the optimization phase is separately carried out in a neural-power software environment using a genetic algorithm (GA). The simulation study was carried out using the MATLAB/R2022a platform to verify the converter performance along with the SFO-based MPPT controller. To validate the real-time test bench results, a 0.2 kW prototype model was constructed in the laboratory, and the results were verified.

5 December 2022 in Materials Today: Proceedings
Verified
Journal Article
Closed access
JJJ. Jeyashanthi
J. Jeyashanthi
JBJ. Barsana Banu
J. Barsana Banu
PMPANDI MAHARAJAN M
PANDI MAHARAJAN M
MRM. Ramuvel
M. Ramuvel

1 December 2011
Verified
Conference Paper
Closed access
PMPANDI MAHARAJAN M
PANDI MAHARAJAN M
PMP. Muthu
P. Muthu
PMPalpandian P M
Palpandian P M
SKS. Kannadasan
S. Kannadasan
This project presents a comparative study of VSI, CSI and Buck Converter based CSI fed BLDC Motor for automotive applications. The aim of the work is to reduce the cost and size of a brushless dc motor (BLDC) drive as well as increase the reliability and ruggedness of the drive. Traditional BLDC drives use Voltage Source Inverter (VSI) that utilize hard switching, thereby generating switching losses and entail the use of large heat sinks. VSI needs a huge dc link capacitor that is inherently unreliable and is one of the most expensive components of the drive. Hence, a Current Source Inverter (CSI) is used to replace the hard switching by soft switching, thereby eliminating the heat sinks as well as the large dc link capacitor. A controlled rectifier together with a large inductor acts as a current source, the only disadvantage is the large value of the dc link inductor and the huge number of turns needed to achieve these values of the inductances lead to huge resistive losses. Therefore, it is shown that it is possible to replace the controller rectifier and the large inductor with a suitable Buck converter based current source inverter can be switched at high frequencies with much smaller value of the dc link inductor without increasing the current ripples. Hence, it is possible to have the advantage of using a CSI as well as reduce the value of the dc link inductor without a corresponding increase in the heat sink. The effectiveness of the VSI and CSI fed BLDC motor schemes are verified through the simulation results.

1 June 2025 in Indonesian Journal of Electrical Engineering and Computer Science
Verified
Journal Article
Open access
PDF file
DKDeeba Kannan
Deeba Kannan
NSNagamuthu Krishnan Sundarasrinivasa Sankaranarayanan
Nagamuthu Krishnan Sundarasrinivasa Sankaranarayanan
SVShanmugasundaram Venkatarajan
Shanmugasundaram Venkatarajan
RMRashima Mahajan
Rashima Mahajan
BGBrindha Gunasekaran
Brindha Gunasekaran
KKarthikeyan Dhandapani
Karthikeyan Dhandapani
In modern agriculture, ensuring plant health is essential for high crop yields and quality. Plant diseases pose risks to economies, communities, and the environment, making early and accurate diagnosis crucial. The internet of things (IoT) has revolutionized farming by enabling real-time crop monitoring and using drones and cameras for early disease detection. This technology helps farmers address challenges with precision and sustainability. This research propose an ensemble learning model incorporating multi-class capsule networks (MCCN) and other pre-trained model with majority voting system is implemented to predict plant diseases and pests early. The research aims to develop a robust MCCN-based ensemble prediction model for timely disease identification. To evaluate the performance of the ensemble model, various key metrics, including accuracy, and loss value, are assessed. Furthermore, a comparative analysis is conducted, benchmarking the MCCN model against other well-known pre-trained models such as residual network-101 (ResNet101), visual geometry group-19 (VGG19), and GoogleNet. This research signifies a substantial stride towards the realization of IoT-driven precision agriculture, where advanced technology and machine learning contribute to the early detection and mitigation of plant diseases, ultimately enhancing crop yield and environmental sustainability.

1 February 2024 in Indonesian Journal of Electrical Engineering and Computer Science
Verified
Journal Article
Open access
PDF file
SGSaurabh Gupta
Saurabh Gupta
PRPalanisamy Ramasamy
Palanisamy Ramasamy
PMPANDI MAHARAJAN M
PANDI MAHARAJAN M
SKSelvakumar Kuppusamy
Selvakumar Kuppusamy
SDSelvabharathi Devadoss
Selvabharathi Devadoss
VKVignesh Kumar
Vignesh Kumar
Solar energy is the most generally accessible energy in the entire globe. Proper solar panel maintenance is necessary to reduce reliance on imported energy. Continuous monitoring of the solar panel's power output is required. The deployment of internet of things (IoT) monitoring of solar panels for maintenance is the basis for the current research. A multi-variable long-term photovoltaic (PV) power production prediction approach based on support vector machine (SVM) is developed in this study with the aim of completely evaluating the influence of PV panels performance and actual operational state factors on the power generation efficiency. This study examines the use of SVM and climatic factors to forecast the long-term output of power from solar panels. A solar power facility in a semi-arid area provided the data utilized in this investigation. Temperature, humidity, wind speed, and sun radiation are some of the meteorological variables that were considered in the study. To anticipate the power generation of the panels, the SVM is trained using the climatic factors and the power generation data. The findings demonstrate that the SVM model consistently predicts the panels' long-term power generation with a high degree of accuracy.