Market demands coating processes with high-performance, high reliability, high flexibility for processing of complex geometries and multi-material depositions, as well as increased deposition rates. The systematic coupling of two plasma transferred arc welding systems that interact in the same melt pool to form a tandem Plasma Transferred Arc (PTA) system accomplishes these tasks. Previous research has shown that the deposition rate with the tandem PTA method reaches 240 percent when comparing to the conventional single torch PTA method. Within one layer, up to four different powders and powder fractions can be combined at the same time. This allows for the creation of multi-material coatings that are suitable for sustaining high mechanical loads and wear- and temperature-resistant surfaces by use of tungsten carbides (WC). This study examines and analyzes defined functionally graded structures made from super duplex steel 1.4410 and corrosion resistant austenitic steel 1.4404. The mechanical-chemical properties of the tandem PTA system can be precisely controlled by changing the powder feeding positions. Furthermore, an additively manufactured specimen from previous studies is examined and evaluated. A direct comparison with conventional single torch PTA was performed to demonstrate the benefits of the tandem PTA-process.
Additive technologies are now widely used for the production of complex precise parts and have high potential for the production of forming dies. In this work, hot-forming dies optimized for additive manufacturing were developed and produced with wire arc direct energy deposition (WA-DED) and laser powder bed fusion (L-PBF) technologies. The concept of lightweight hot-forming dies with a 2D-lattice structure was developed, which reduced the weight of each die by 56%, from 14.2 kg to 6.1 kg, in production using L-PBF. Maraging/precipitation-hardened steel 17-4PH was used as an alternative to traditional hot-working steels with slightly lower mechanical properties and a much higher processability in the additive manufacturing process. The workability of the manufactured dies was confirmed by forging tests on an industrial screw press.
Prediction of the evolution of material properties during the AM process based on the FEM simulation and experimental results HÄRTEL Sebastian, SZYNDLER Joa
Intermetallic Fe3Al-based alloys reinforced with Laves-phase precipitates are emerging as potential replacements for conventional high-alloy steels and possibly polycrystalline Ni-based superalloys in structural applications up to 700 °C. Their impressive mechanical properties, however, are offset by limited fabricability and poor machinability due to their severe brittleness. High tool wear during finish-machining, which is still required for components such as turbine blades, remains a key barrier to their broader adoption. In contrast to conventional manufacturing routes, additive manufacturing offers a viable solution by enabling near-net-shape manufacturing of difficult-to-machine iron aluminides. In the present study, laser powder bed fusion was used to produce an Fe-25Al-1.5Ta intermetallic containing strengthening Laves-phase precipitates, and the porosity, microstructure and phase composition were characterized as a function of the process parameters. The results showed that preheating the build plate to 650 °C effectively suppressed delamination and macrocrack formation, even though noticeable cracking still occurred at the high scan speed of 1000 mm/s. X-ray tomography revealed that samples fabricated with a lower scan speed (500 mm/s) and a higher layer thickness (0.1 mm) contained larger, irregularly shaped pores, whereas specimens printed at the same volumetric energy density (40 J/mm3) but with different parameter sets exhibited smaller fractions of predominantly spherical pores. All samples contained mostly elongated grains that were either oriented close to relative to the build direction or largely texture-free. X-ray diffraction confirmed the presence of Fe3Al and C14-type (Fe, Al)2Ta Laves phase in all samples. Hardness values fell within a narrow range (378–398 HV10), with only a slight reduction in the specimen exhibiting higher porosity.
In the Laser Powder Bed Fusion (LPBF) process for metal components, a CAD file is sliced into layers with a thickness of 20-80 micrometers and the component is built up layer by layer. For this purpose, a metal powder layer is applied in each case and melted locally. This process is repeated until the geometry is completely established. The mechanical properties of the manufactured part are controlled by the cooling rate. It is currently not considered in the design of LPBF components, that the printed part has a varying heat flow into the surrounding powder and into the support plate depending on its slenderness. As a result of the different temperature histories, different microstructures with correspondingly different mechanical properties are formed in the untreated state (as-built). These differences must be considered in the component design. In this work, walls of various thicknesses were produced from 316L stainless-steel alloy using the LPBF process. The walls could be used to create plane-strain-compression-test specimens of various heights and orientations. The tests were performed according to Graf et al. [1] and the flow curve was calculated from the force-displacement curve while taking friction into account. Following that, tensile strength, Young’s modulus, yield strength, and yield stress were determined inversely. A clear dependence of the mechanical parameters on the degree of slimness was discovered, which was confirmed by microscopic examinations. To summarize, the plane-strain-compression-test is a quick and reliable method for determining the local variation of mechanical properties.
Hot forging is a forming process that can be used as a post-processing treatment to close residual porosity and refine the microstructure of additively manufactured materials, resulting in improved mechanical properties. During hot forging, void closure occurs through plastic deformation resulting from a predominantly compressive stress state at elevated temperatures. In the present work, Fe-25Al-1.5Ta (at. %) samples have been produced by laser powder bed fusion (LPBF) using a larger layer thickness and scan speed than commonly used to achieve a target porosity fraction of approximately 10%. Full densification is attempted in the subsequent hot compression step at various height reduction ratios. The as-built LPBF samples contained 8-10% voids. After deformation to true strains of 0.2, 0.4, and 0.6, the void fraction decreased significantly to approximately 4%, 2.3%, and 1.1%, respectively. Hot compression resulted in the complete closure of large pores with a size range of 200-300 µm and a significant reduction in the size of small to medium pores. These results show potential for improving the productivity of the LPBF by speeding up the process by increasing layer thickness and scanning speed while maintaining a reasonable density. Full densification should be achieved by subsequent hot forging.